Huawei Aolynk DR814Q ADSL2+ Скачать руководство пользователя

Страница: 62 / 84

User Manual
Aolynk DR814Q ADSL2+ Broadband Router

6 Troubleshooting

The DNS server IP address specified on the PC is correct. If you specify the PC to

obtain the DNS server address dynamically, verify with your ISP that the address

configured on the DR814Q is correct, and then you can use the ping utility to test

the connectivity with your ISP’s DNS server.

2) Generally, if a host can ping the Internet IP address, but cannot open the Web

pages, the DNS server of the ISP is experiencing a failure temporarily. In this case,

you can choose either of the following to solve the problem: Manually change your

PC’s DNS IP address to the address of a normally functioning DNS server. Log

into the Web page of the DR814Q and manually modify the configuration for DNS

Relay (refer to section 4.2.2 “DNS Relay"), and then check by the

nslookup

command as instructed in section 6.2.2 “Nslookup”.

Symptom 8

: Fail to save the changes made on the Web-based configuration pages.

Solution

: Make sure that you click <Apply> to confirm every change you have made.

After completing all the settings, enter the [Save Configuration] page to save them, thus

making them take effect when the DR814Q is powered on next time.

Symptom 9

: You can visit most websites successfully, while access to some websites

fails due to timeout. Configuring the DR814Q to operate in the bridge mode and your

PC to establish a dialup connection can solve this problem.

Solution

: This may be caused by an over-high MTU value set on the router between

the user end and the website. Usually you can set a small MTU value (1440, for

example) on the detail setting page of the WAN service to avoid this problem. Refer to

section 4.2.1 “WAN” for detailed operations.

Symptom 10

: Some services are unavailable once the firewall is enabled.

Solution

: As the firewall rules of the DR814Q are very strict, it is recommended

someone familiar with the WAN services and router configuration enable the firewall

and configure the firewall rules. Before the creation of firewall rules, you must be clear

about the Internet service deployment. It is recommended that you disable the firewall.

6.2 Diagnosis Tools

6.2.1 Ping

Use

the

ping

command to check whether your PC can recognize other computers on

the network. A

ping

command sends messages to the specified computer. If the

computer receives the messages, it replies with the response message. Before using

the command, you must know the IP address of the destination host with which your PC

is trying to communicate.

At the DOS prompt, enter the following command:

ping 192.168.1.1

If the destination host receives the packet, the command prompt window displays the

contents as shown in Figure 6-1.

Содержание Aolynk DR814Q ADSL2+





















































































Результаты поиска

Содержание Aolynk DR814Q ADSL2+

Отзывы:

Похожие инструкции для Aolynk DR814Q ADSL2+

Бренды по названию

Популярные бренды

Huawei Aolynk DR814Q ADSL2+, Руководство пользователя

Результаты поиска

Содержание Aolynk DR814Q ADSL2+

Отзывы:

Похожие инструкции для Aolynk DR814Q ADSL2+

Бренды по названию

Популярные бренды