Huawei 7810 Скачать руководство пользователя

Страница: 38 / 191

Huawei IP Phone eSpace
7810&7820&7830&7850&7870&7803X
Administrator Guide

2 Single IP Phone Configuration

Issue 01 (2011-12-31)

Huawei Proprietary and Confidential

Table 2-14

Other advanced network parameters

Parameter

Description

Port Link

WAN Port Link

Network connection rate for the network port. The options are as
follows:



auto negotiate

: An IP phone selects a connection mode based on

the network environment.



full duplex, 10 Mbps



full duplex, 100 Mbps



half duplex, 10 Mbps



half duplex, 100 Mbps

Only

auto negotiate

is available to eSpace 7870.

PC Port Link

Network connection rate for the PC port. The options are as follows:



auto negotiate

: An IP phone selects a connection mode based on

the network environment.



full duplex, 10 Mbps



full duplex, 100 Mbps



half duplex, 10 Mbps



half duplex, 100 Mbps

Only

auto negotiate

is available to eSpace 7870.

QoS

Voice QoS

Voice QoS.

Value range: 0 to 63

SIP QoS

Signaling QoS.

Value range: 0 to 63

Local RTP Port

MaxRTPPort

Maximum port number.

MinRTPPort

Minimum port number. The value must not be greater than the value
of

MaxRTPPort

SNMP (It is unavailable to eSpace 7870.)

Port

Port number for listening on the IP phone.

Trusted Address

IP address of the management device, for example, a PC. A maximum
of three IP addresses are supported. Separate each two IP addresses
with a space character.

WebServer

HTTP port

Port number used for using HTTP to access web pages.

Default value: 80

HTTPS port

Port number used for using HTTPS to access web pages.

Содержание 7810
































































































































































































Результаты поиска

Содержание 7810

Отзывы:

Похожие инструкции для 7810

Бренды по названию

Популярные бренды

Huawei 7810, Руководство администратора

Результаты поиска

Содержание 7810

Отзывы:

Похожие инструкции для 7810

Бренды по названию

Популярные бренды