background image

 

2    Safety, Preparation and Examination 

2.1 Preparation for use 

This instruction is a detailed description of the Movement, Storage, Installation, Startup, Operation 
condition, Maintenance, troubles & solutions and Repairing. 
The installation of machine is suggested to be operated by trained person. 
 

Pls follow the maintenance instructions 

 

Before operating the machine, pls be sure to read the operation manual carefully and fully 
understand it. 

 

If there is any question, pls contact the supplier. 
 

2.2 Precautions on safety 

 

Pls confirm the machine voltage, frequency to prevent the accident.   

 

This machine is in power system of single-phase three-wire, and the yellow and green wire is 
protective earth wire which should be grounding and could not be removed. 

 

The power cord should be protected from pressing, pulling, and should be winded when it is not 
used. 

 

Do not touch the electrical devices inside the machine after the power is turned on. 

 

Do not touch any driving parts to avoid injury when the machine is in operation. 

 

Do not open the machine hull, protection cover etc. when machine is on so as to avoid pinching, 
scalding or electric shock. 

 

Do not touch the heating blocks to prevent from burns. 

 

When the machine is repaired, please proceed when the heating blocks are fully cool to avoid burns. 

 

Do not use the machine in corrosive and dusty environments. 

 

Do not optionally replace parts on the machine. 

 

Keep the inside and outside of the machine clean and remove the surface adhesive materials from 
the Teflon belt in time. 

 

Fill and exchange oil in worm-gear case regularly, and oil gear and sprocket (YP7408 semi-liquid gear 
oil). 

 

When the machine is not in use, the power supply and air supply should be switched off. 

 

Keep this manual properly for easy reference in the future. 

 

This machine is produced as per the latest technology and security standard. There may be danger 
or damage under improper operation. Please notice the keywords “DANGEROUS”, “WARNING”, 
“TAKE CARE”.   

E.g.: 

 

DANGEROUS! 
Ignorance of this notice will lead to damage even fatal accidence. 

 

 

WARNING! 
Ignorance of this notice will lead to damage even fatal accidence. 

 

 

Содержание FRM-980I

































Отзывы: