manualshive.com logo in svg

HTP CGH-199O Series, Установка, Запуск, Обслуживание, Запасные Части и Гарантия, Страница: 26 / 60

Поделиться
Скачать
HTP CGH-199O Series Скачать руководство пользователя страница 26

lp-673 Rev. 000 Rel. 001 Date 8.30.18

26

Outdoor Installation

When drawing combustion air from the outdoors, care must be taken to provide adequate freeze protection. Failure to do so could result in 

property damage and premature product failure. Such damages and failures ARE NOT covered by product warranty.

CAUTION

This water heater is designed to draw combustion air through the louver system in the water heater cabinet. This combustion air also serves 

to cool the internal electronics when the heater is installed in very warm climates.

To prevent combustion air contamination or exhaust recirculation:

•  Flue gas can cause damage to exterior walls and other devices.

•  Locate the heater at least 48” below or horizontally from any window, door, walkway, or gravity air intake.

•  Locate the heater 10’ away from any public area, outdoor sitting area, or forced air inlet.

•  Locate the heater away from areas that may change over time. Do not allow the growth of trees, shrubs, or plants to obstruct proper 

operation of the exhaust vent system.

•  If the heater is located in a fenced area, ensure the unit exhaust extends level with or above the top of the fence to ensure flue gas does 

not get trapped and possibly recirculated into the louver system, which could contaminate the combustion air.

INLET

NOTE:  DIMENSIONS GIVEN ARE IN FEET.

WINDOW

FORCED AIR

ENTRY DOOR

EXISTING BUILDING

  10' MIN.

  4' MIN.

  4' MIN.   

  4' MIN.  

RECOMMENDED CLEARANCE FOR OUTDOOR INSTALLATION

LP-672-E

4/5/18

Figure 17 - Recommended Outdoor Installation Clearances

LP-672-F

04/5/18

NOTE: IN EXTREMELY HOT CLIMATES IT IS RECOMMENDED TO PLACE THE UNIT ON THE NORTH SIDE

OF THE BUILDING TO EXTEND THE LIFE OF THE CONTROLS.

RECOMMENDED OUTDOOR ENCLOSURE

FENCING SHOULD

NOT EXCEED HEIGHT

OF THE UNIT

TOP VIEW

  4' MIN.

  4' MIN.

  4' MIN.

Figure 18 - Recommended Outdoor Enclosure

Heaters must not be installed under an overhang 

unless clearances are in accordance with local 

codes, the requirements of the gas supplier / utility, 

and the AHJ. At a mininum, do  not  install  this 

water  heater  under  an overhang less than 3 ft

(915 mm) from its top or eaves.  The area under an

overhang must be open to three sides. Roof water 

drainage must be diverted away from heaters

installed under overhangs. Failure of heater or 

components due to incorrect operating conditions 

IS NOT covered by product warranty. 

3 ft

(915 mm)

lp-672-C

Rev. 5.18.18

Содержание CGH-199O Series





























































Отзывы:

Нет отзывов