background image

 

HT7052 

 

EN - 33

9 MAINTENANCE 

9.1 GENERAL 

INFORMATION 

The instrument You purchased is a precision instrument. During use and storage, carefully 
observe the recommendations listed in this manual in order to prevent possible damage or 
dangers during use. Do not use the instrument in environments with high humidity levels or 
at high temperatures. Do not directly expose to sunlight. Always turn off the instrument 
after use. Never remove the front panel of the instrument. The instrument don’t need any 
particular maintenance 

9.2  REPLACEMENT AND CHARGING BATTERIES 

The instrument is power-supplied through internal rechargeable batteries which are 
recharged from the mains by means of a battery charger integrated in the instrument itself. 
The symbol “

“ illuminated in the left bottom part indicates that the batteries are flat 

and must be recharged 

 

 

CAUTION 

 

  Connect the instrument to the mains power supply for 20 hours to fully 

charge batteries. (typical charging current is 600mA). When you charge the 
batteries for the first time, it normally takes about 3 charge and discharge
cycles for the batteries to regain full capacity 

  The operator does not need to disconnect the instrument from mains 

supply after the full recharging period. The instrument can be connected 
permanently 

  The instrument will only work when rechargeable batteries are inside the 

instrument 

 

In case of batteries replacement follow the herewith steps: 

 

 

CAUTION 

 

Nominal power supply voltage is 7.2 V DC. Use only six NiMH cells with 
size equivalent to IEC LR20 (diameter = 33 mm, height = 58 mm) 

 

1.  Turn the power off and disconnect any measurement accessories or mains supply 

cable connected to the instrument before opening the battery cover to avoid electric 
shock 

2.  Remove the two screws (see Fig. 1 – Part 15) and open the battery cover 
3.  Replace all the six batteries with others of the same type respecting the indicated 

polarity 

4.  Restore the battery cover 
5.  Use the appropriate battery disposal methods for your area 

9.3  CLEANING THE INSTRUMENT 

To clean the instrument, use a soft dry cloth. Never use humid cloths, solvents, water, etc 

 

9.4  END OF LIFE 

 

Warning: the reported symbol indicates that the appliance, the batteries and its 
accessories must be disposed of separately and treated correctly 

 

Содержание HT7052








































Отзывы: