HT Italia HT7052 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 39

background image

HT7052

EN - 3

1.2 DURING

USE

Carefully read the following recommendations and instructions:

CAUTION

Failure to observe the warnings and/or instructions may damage the
instrument and/or its components or generate a danger for the operator. If,
during use, the low battery symbol appears on the display, insert the supply
cable into the Europlug socket to start battery recharge. During battery
recharge, it is possible to perform measurements



Before selecting a new function, disconnect the measuring probes from the circuit



When the instrument is connected to the circuit being tested, never touch any unused

lead



Avoid measuring resistance with external voltages. Even if the instrument is protected,

as an excess voltage may cause instrument malfunctions



In case of a capacitive test object (long tested cable etc.), automatic discharge of the

object may not be done immediately after finishing the measurement – “Please wait,
discharging” message will be displayed



Handling with capacitive loads note that 40nF charged to 1kV or 5nF charged to 10 kV

are hazardous live

1.3 AFTER

USE

When measurements are completed, turn off the instrument by pressing the ON/OFF key

1.4 DEFINITION OF MEASUREMENT (OVERVOLTAGE) CATEGORY

Standard "IEC/EN61010-1: Safety requirements for electrical equipment for measurement,
control and laboratory use, Part 1: General requirements", defines what is intended for
measurement category, commonly known as overvoltage category. In § 6.7.4: Measuring
circuits, it reads:

Circuits are divided into the following measurement categories:



Measurement category IV

is for measurements performed at the source of a low-

voltage installation

Examples are electric counters and measurements on primary devices protecting

against overcurrents and on ripple adjusting units



Measurement category III

is for measurements performed on installations inside

buildings

Examples

are

measurements

performed on distribution boards, circuit breakers, wiring

harnesses, including cables, bars, junction boxes, switches, sockets of fixed
installations and appliances designed for industrial use and other equipment, e.g.
stationary motors connected to fixed systems



Measurement category II

is for measurements performed on circuits directly

connected to the low-voltage installation

Examples are measurements performed on household appliances, portable tools and
similar equipment



Measurement category I

is for measurements performed on circuits not directly

connected to the MAINS

Examples are measurements performed on circuits not derived from the MAINS and on
circuits derived from the MAINS provided with a special (internal) protection. In this
latter case, the stress caused by the transients is variable; therefore, (OMISSIS) it is
necessary that the user knows the appliance’s resistance to transients

«
...
3
4
5
6
7
...
»

Содержание HT7052








































Отзывы:

Нет отзывов

Похожие инструкции для HT7052

Бренд: Yamaha Страницы: 69

LM-OG-P2 Advanced

Бренд: Badger Meter Страницы: 48

Бренд: Badger Meter Страницы: 24

Бренд: Bahco Страницы: 92

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Stage Piano MP8

Бренд: Kawai Страницы: 70

Бренд: Make Noise Страницы: 15

Бренд: Major tech Страницы: 40

Бренд: Fender Страницы: 20

Comark Diligence 600

Бренд: Fluke Страницы: 61

Бренд: A-CUBE Страницы: 25

Бренд: Aalborg Страницы: 56

Бренд: VOLTCRAFT Страницы: 8

Panel Scope VPS10

Бренд: Velleman Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды