HS Tarm 2000 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 66

background image

O

PERATING

Y

OUR

B

OILER (continued)

PAGE 44

______________________________________________________________________________________________________________________________________________________________________________________

REGULAR STOKING OF THE BOILER (continued)

If The Draft Fan is

OFF

: (BOILER TEMPERATURE BELOW 140

°

F)

NOTE:

When the boiler temperature is below 140

°

F the assumption is that the fire has burned out

and that hot gases are not present. However, never quickly open the door unless you
have tried to vent hot gases from the firebox first.

1. Open the by-pass damper.
2. Turn the reset switch off and back on to activate the draft fan. Let the fan run for 2

minutes.

3.  Turn off the fan by switching the reset switch off.
4.  Immediately open the loading door ¾” with your left hand.
5.  Wait approximately 20 seconds before opening the load door slowly, cautiously and fully.
6.  If there are sufficient live coals left in the firebox to re-ignite the next load of wood you

will not need to use paper to restart the fire. Place several pieces of dry kindling in the
center of the firebox over the slot in the refractory and rake the live coals from the sides
of the firebox to the center on top of the kindling.

7. Add enough firewood to carry the estimated heat load for the next 8 hours as per the

“Operational Procedures” on page 45 which are very important.

8. Close the load door and immediately turn “ON” the draft fan switch (F). Close and latch

the by-pass by pushing in and down forcefully so that the spring will keep it closed.

9. HOWEVER, if you find very few live coals left in the firebox after opening the load door in

step #3 above, follow steps #3-#9 on page 40 to restart the fire.

If The Draft Fan Is

ON

:

1. Open the by-pass damper.

2. WAIT, 2-3 minutes with the draft fan running.

3. Turn off the draft fan by using the power switch on the control panel.

4. Without delay, open the loading door 3/4” with your left hand.

5. Wait approximately 20 seconds.

6. Open the loading door slowly, fully, and cautiously!

7. Load the firebox if the previous load has burned down to low coals, placing the wood

uniformly front to back and tight together, not crosswise.

8. Close the loading door.

9. Turn the draft fan back on by switching the power switch “ON” on the control panel.

10. Close the by-pass damper.

HEAT DEMAND ON THE BOILER

In order to achieve the best combustion efficiency and the longest boiler life with the least
amount of creosote in the combustion chamber, it is necessary that there be a reasonable
demand for heat when the boiler is operating on wood.

44

«
...
47
48
49
50
51
...
»

Содержание 2000



































































Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: Magikitch'n Страницы: 20

ENHANCED 2 Series

Бренд: U.S. Boiler Company Страницы: 60

Бренд: MONTAGUE Страницы: 36

Copper Brute ll BWCH

Бренд: Bradford White Страницы: 16

RemaSol200SE-2S

Бренд: REMEHA Страницы: 80

Бренд: Biodom Страницы: 50

Бренд: Ariston Страницы: 10

Бренд: Hamworthy Страницы: 48

Бренд: elco Страницы: 96

Бренд: Columbia Страницы: 32

LOGIC+ COMBI C35

Бренд: Ideal Heating Страницы: 72

Concord CXS 40H

Бренд: Ideal Boilers Страницы: 4

Бренд: H2O Страницы: 50

Бренд: E.L.M. Leblanc Страницы: 24

Бренд: Burnham Страницы: 8

Бренд: Ferroli Страницы: 68

Бренд: Sime Страницы: 32

MagnaTherm HTD Series

Бренд: Laars Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды