HS Tarm 2000 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 66

background image

I

NSTALLATION (continued)

PAGE 28

_____________________________________________________________________________________________________________________________________________________________________________________

By-Pass Damper Adjustment

The by-pass lever is adjusted at the factory, but should be checked, as correct adjustment is
essential for proper combustion. To check adjustment, push the by-pass knob in and down.
With a firm push, it should lock into place on the bracket. If the stop on the rod is engaged on
the bracket but the handle still has front to back play, or, if the handle will not push in far
enough to engage the stop, the by-pass must be adjusted. To do so, loosen the nut at the rear
of the rod and rotate the rod to tighten or loosen the adjustment. To complete the adjustment,
make sure the welded stop rod is pointed downward, and tighten the locknut.

Turbulators

Turbulators should be located in the oil or gas heat exchange tubes when the boiler is received.

Please check to be sure they are located correctly and that they are not in the wood heat
exchange tubes in error.

Installation of Back-Up Fuel Burner

Either an oil, propane gas (LPG) or natural gas (NG) burner may be used to provide back-up or
full-time heat with the EXCEL boiler.

Individual instruction manuals are provided in the box with each oil or gas burner. In addition,
the following information is necessary and important:

•

Before installing the burner, if necessary, trim the hole in the burner door brick with a
knife so that the burner can be inserted through the opening.

•

120 Volt AC power feed for the oil or gas burner is wired to “B” and “N” terminals inside

the boiler Control Panel. The “T” terminals on the burner primary control must be
connected to the #7 and #8 terminals on the 24 Volt terminal strip on the Control Panel
housing.

NOTE: 1.

IF THE OIL OR GAS BURNER IS IMPROPERLY INSTALLED, NOT

INSTALLED AND/OR NOT SERVICED ON A REGULAR BASIS, DAMAGE
TO THE BOILER MAY RESULT.

2. BURNER INSPECTION AND TUNE-UP SHOULD BE DONE NOT LESS

THAN ONCE PER YEAR BY A QUALIFIED HEATING CONTRACTOR OR
BURNER SPECIALIST. DAMAGE TO THE BOILER OR PARTS DUE TO
IMPROPER INSTALLATION MAY NOT BE COVERED UNDER WARRANTY!

Oil Burner Installation (refer to Oil Burner Manufacturer’s Instruction Manual)

If the Tarm EXCEL is to be fired on oil, a flame-retention burner MUST be used. A BECKETT

AF burner is standard equipment. Oil burners must be adjusted with test equipment, not “by

eye”. A minimum .04 in./wc draft is required. The nozzle specifications are as follows:

•

TARM EXCEL 2000

•

TARM EXCEL 2200

80

°

Delavan B--- .75 to 1.10 GPH

80

°

Delavan B--- .75 to 1.35 GPH

NOTE:

The Beckett AF burner must be equipped with an F-6 retention head for operation

with 1.10GPH or greater nozzle. An F3 head is standard with the burner. An F-6
retention head is shipped with an EXCEL 2200.

28

«
...
31
32
33
34
35
...
»

Содержание 2000



































































Отзывы:

Нет отзывов

Похожие инструкции для 2000

Бренд: Raypak Страницы: 213

Бренд: Froling Страницы: 31

GRAND PELLET 100

Бренд: Metal-Fach Страницы: 60

Бренд: MIKOTERM Страницы: 38

Бренд: IDEAL Страницы: 44

Бренд: Navien Страницы: 4

Бренд: Lang Страницы: 16

AAA-3000 series

Бренд: Super Hot Страницы: 36

Бренд: Reliable Страницы: 1

Бренд: Radijator Страницы: 83

Vitodens 222-F B2TA series

Бренд: Viessmann Страницы: 196

THERMIFIC MODU-FIRE

Бренд: Patterson-Kelley Страницы: 27

VITORONDENS 200-T

Бренд: Viessmann Страницы: 32

Vitorond 200 Series

Бренд: Viessmann Страницы: 28

Бренд: Viessmann Страницы: 32

VITORADIAL 300-T

Бренд: Viessmann Страницы: 48

VITOLIGNO 300-P

Бренд: Viessmann Страницы: 60

VITODENS 200 WB2B

Бренд: Viessmann Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды