HP ProLiant ML350p Gen8 Скачать руководство пользователя страница 87

Страница: 87 / 101

Component identification 87

Hot-plug drive LED definitions

Item LED

Status

Definition

Locate

Solid blue

The drive is being identified by a host application.

Flashing blue

The drive carrier firmware is being updated or requires an update.

Activity ring

Rotating green

Drive activity

Off

No drive activity

Do not remove

Solid white

Do not remove the drive. Removing the drive causes one or more of

the logical drives to fail.

Off

Removing the drive does not cause a logical drive to fail.

Drive status

Solid green

The drive is a member of one or more logical drives.

Flashing green

The drive is rebuilding or performing a RAID migration, strip size

migration, capacity expansion, or logical drive extension, or is
erasing.

Flashing

amber/green

The drive is a member of one or more logical drives and predicts

the drive will fail.

Flashing amber The drive is not configured and predicts the drive will fail.

Solid amber

The drive has failed.

Off

The drive is not configured by a RAID controller.

Fans

IMPORTANT:

Fan louvers must be present for the redundant configuration. Without the louvers,

all four fans are nonredundant.

Содержание ProLiant ML350p Gen8






































































































Результаты поиска

Содержание ProLiant ML350p Gen8

Отзывы:

Бренды по названию

Популярные бренды

HP ProLiant ML350p Gen8, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant ML350p Gen8

Отзывы:

Бренды по названию

Популярные бренды