HP ProLiant ML350p Gen8 Скачать руководство пользователя страница 82

Страница: 82 / 101

Component identification 82

Item

Description

Internal USB tape connector

Discovery service cable connector

System battery

SATA connectors

Internal USB connector

Processor 2 DIMM slots

TPM connector

System maintenance switch

NMI header

Slot 9 PCIe3 x8 (4, 1)

Slot 8 PCIe3 x16 ( 16, 8, 4, 1)

Slot 7 PCIe3 x8 (4, 1)

Slot 6 PCIe3 x16 (16, 8, 4, 1)

Slot 5 PCIe2 x8 (4, 1)

Processor 1 DIMM slots

Processor socket 1 (populated)

System maintenance switch

Position

Default

Function

Off

Off = iLO 4 security is enabled.

On = iLO 4 security is disabled.

Off

Off = System configuration can be
changed.

On = System configuration is locked.

Off

Reserved

Off

Reserved

Off

Off = Power-on password is enabled.
On = Power-on password is disabled.

Off

Off = No function

On = ROM reads system configuration
as invalid.

—

Reserved

—

Reserved

—

Reserved

S10

—

Reserved

S11

—

Reserved

S12

—

Reserved

To access the redundant ROM, set S1, S5, and S6 to on.
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all

system configuration settings from both CMOS and NVRAM.

CAUTION:

Clearing CMOS and/or NVRAM deletes configuration information. Be sure to

properly configure the server or data loss could occur.

Содержание ProLiant ML350p Gen8






































































































Результаты поиска

Содержание ProLiant ML350p Gen8

Отзывы:

Бренды по названию

Популярные бренды

HP ProLiant ML350p Gen8, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant ML350p Gen8

Отзывы:

Бренды по названию

Популярные бренды