HP ProCurve 8116fl Скачать руководство пользователя страница 80

Страница: 80 / 134

Replacing Hardware

Replacing Compact Flash Card

Repla

g Hard

The Compact Flash card is the primary non-volatile storage medium located
on the management module that contains both the boot software and
configuration files.

To install (or replace) a Compact Flash card:

1. Remove the management module. (You cannot access the Compact Flash

when the management module is installed. This prevents inadvertent
removal of the system image while the system is running.)

2. Insert the Compact Flash and snap it into place. (The Compact Flash is

keyed so it only goes in one way.) See the following illustration for details.

2. Snap bail over card

to retain in place

1. Insert Compact

Flash card into slot

Management Module

Compact Flash
Memory card

DIMM Slots (2)

Compact Flash
Memory card

PCMCIA Card Slot

3. Reinstall the management module according to the procedures described

“Installing a Management Module” on page 2-20

N o t e

The system software image file normally is stored on the Compact Flash card,
but can also be stored on a TFTP server or BootP server.

4-8

Содержание ProCurve 8116fl







































































































































Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды

HP ProCurve 8116fl, Руководство по установке и началу работы

Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды