HP ProCurve 5400zl Series Скачать руководство пользователя страница 16

Страница: 16 / 135

1-6

Introducing the HP 5400 zl Switches

Network Connectivity, Speeds and Technologies

Introducing the HP 5400 zl

Switches

Network Connectivity, Speeds and
Technologies

These products support optional network connectivity as follows:

Table 1-1.

Optional Network Connectivity, Speeds and Technologies

Transceiver Form-Factor and Connector

Speed

Technology

Cabling

SFP ("mini-GBIC")

Connector

SFP+

Connector

100 Mbps

100-FX

Fiber (multimode)

100-BX

Fiber (single mode)

1 Gbps

1000-T

Copper (twisted-pair)

RJ-45

1000-SX

Fiber (multimode)

1000-LX

Fiber (multimode or single mode)

1000-LH

Fiber (single mode)

1000-BX

Fiber (single mode)

10 Gbps

10-Gig CX4

Copper (twinaxial)

CX4

10-Gig
Direct Attach

Copper (twinaxial)

Not

Applicable

10-Gig SR

Fiber (multimode)

10-Gig LRM

Fiber (multimode)

10-Gig LR

Fiber (single mode)

10-Gig ER

Fiber (single mode)

For supported transceivers, visit

www.hp.com/networking/support

– In the first textbox, type

J4858

(for 100-Mb and Gigabit information), or

J8436

(for 10-Gigabit information).

– Select any of the products that display in the dropdown list.
– Select

Product support information

. Then click on

Manuals

and find the

Transceiver Support Matrix

For technical details of cabling and technologies see "Cabling and Technology Information" in the appendices.

Содержание ProCurve 5400zl Series








































































































































Результаты поиска

Содержание ProCurve 5400zl Series

Отзывы:

Похожие инструкции для ProCurve 5400zl Series

Бренды по названию

Популярные бренды

HP ProCurve 5400zl Series, Руководство по установке и началу работы

Результаты поиска

Содержание ProCurve 5400zl Series

Отзывы:

Похожие инструкции для ProCurve 5400zl Series

Бренды по названию

Популярные бренды