HP NJ2000 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 44

background image

3Com Network Jack NJ2000

Page 34 of 44

Copyright © 2009 3Com Corporation. All Rights Reserved.

LLDP Configuration

This page allows you to setup the

LLDP

configuration.

The LLDP State table contains a row for each port and two columns. The two columns are:

Port

- The front-panel port number.

State

- You can choose to disable or enable LLDP for each port. Enabling LLDP will allow the port to

receive and transmit TLVs.

There are three main buttons associated with this page:

HELP

- Displays this window.

APPLY

- Updates the switch configuration. No changes are made to the configuration until this button is

pressed.

REFRESH

- Reloads the current page with the latest configuration settings.

LLDP

Link Layer Discovery Protocol (LLDP) allows devices on the network to share information about themselves for the
reasons of simplified troubleshooting, enhanced network management, and maintaining an accurate network
topology. LLDP-capable devices periodically transmit information in messages called Type Length Value (TLV)
fields to neighbor devices. This information includes port description, system name, system description, system
capabilities, and management address.

«
...
32
33
34
35
36
...
»

Содержание NJ2000













































Отзывы:

Нет отзывов

Похожие инструкции для NJ2000

Бренд: CAME Страницы: 2

Бренд: Datavideo Страницы: 2

Бренд: Movie Vision Страницы: 2

Бренд: SMC Networks Страницы: 2

Бренд: Omega Engineering Страницы: 8

Бренд: StarTech.com Страницы: 24

EtherDevice EDS-4009 Series

Бренд: Moxa Technologies Страницы: 18

Бренд: TP-Link Страницы: 2

Бренд: AVLT-Power Страницы: 12

Бренд: Enttec Страницы: 22

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

Бренд: Magnum Страницы: 3

Cyber SWITCH 1000

Бренд: Cabletron Systems Страницы: 106

S12500G-AF Series

Бренд: H3C Страницы: 105

Бренд: Black Box Страницы: 74

Бренд: Icy Box Страницы: 10

Бренд: hager Страницы: 3

Бренд: LINK-MI Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды