HP NJ2000 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 44

background image

3Com Network Jack NJ2000

Page 28 of 44

Copyright © 2009 3Com Corporation. All Rights Reserved.

Packet Type

PCs should be connected to ports with

Packet Type

set to

All

. PCs cannot, in general, send or receive

tagged packets.

Switches should be connected to each other with

Packet Type

set to

Tagged

.

If the

Packet Type

is set to

All

, the port can accept incoming tagged and untagged packets. Untagged

packets will be associated with the VLAN identified by the PVID. Tagged packets will be dropped unless
the port is a member of the VLAN identified by the VLAN tag in the packet. Outgoing packets will be
tagged unless the packet's VLAN ID is the same as the PVID.

If the

Packet Type

is set to

Tagged

, the port will drop untagged packets and will only send and receive

tagged packets. Tagged packets will be dropped unless the port is a member of the VLAN identified by the
VLAN tag in the packet. The PVID has no effect in this case.

«
...
26
27
28
29
30
...
»

Содержание NJ2000













































Отзывы:

Нет отзывов

Похожие инструкции для NJ2000

Бренд: Datavideo Страницы: 2

SmartSwitch 6500

Бренд: Cabletron Systems Страницы: 62

Underwater Switch 24V DC/DMX/02

Бренд: Oase Страницы: 40

Aeotec Micro Smart Energy Switch G2

Бренд: Aeon Labs Страницы: 11

Бренд: Witura Страницы: 21

Бренд: DAB Страницы: 56

MicroHub GUH274W3

Бренд: IOGear Страницы: 1

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

S6520X-EI Series

Бренд: H3C Страницы: 34

Бренд: Accton Technology Страницы: 10

Бренд: Lancom Страницы: 23

Бренд: Wavetronix Страницы: 3

Бренд: IPGARD Страницы: 2

Бренд: Alloy Страницы: 33

Бренд: KanexPro Страницы: 35

Бренд: C&C TECHNIC Страницы: 2

Бренд: KinAn Страницы: 5

Бренд: ATEN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды