HP LaserJet 9040/9050 - Multifunction Printer Скачать руководство пользователя страница 32

Страница: 32 / 56

Control-panel messages

The following table explains device messages that might appear on the control panel.

Table 3-2

Control-panel messages

Control panel message

Description

Recommended action

CLOSE FRONT DOOR ON LEFT
ACCESSORY

The stapler door is open or is not closed
correctly.

Close the stapler door correctly.

CLOSE TOP COVER ON LEFT
ACCESSORY

The door is open or is not properly closed.

Close the top door.

DIFFERENT PAPER SIZES IN JOB

Different paper sizes are used for a single job. Verify that all pages in the job are configured

for the same size of paper.

FINISHING UNAVAILABLE

A failure has occurred with the finishing
process.

Remove all media from the bins. If the error
message reappears, record the message
and call for support.

INSTALL BOOKLET BIN

The booklet bin is not correctly installed.

Verify that the booklet bin is correctly
installed.

INSTALL STAPLER UNIT

The stapler unit is not correctly installed.

Verify that the stapler unit is correctly
installed.

OPTIONAL BIN 01 FULL

The stacker bin is full.

Remove all media from the stacker bin.

OPTIONAL BIN 02 FULL

The booklet bin is full.

Remove all paper from the booklet bin.

OUTPUT PAPER PATH OPEN

The accessory on the left side is not correctly
attached.

Verify that the accessory is correctly
attached.

STAPLE AREA SAFETY PROTECTION
ACTIVATED

A staple safety alert has occurred.

Remove any obstruction from the stacker bin
ejection area.

STAPLER LOW ON STAPLES

The stapler cartridge has 20 to 50 staples
remaining.

Replace the staple cartridge if you want to
saddle stitch more than 10 sets in a job.

STAPLER OUT OF STAPLES

The stapler cartridge contains no more
staples.

Replace the stapler cartridge.

See

Load the stapler cartridge on page 17

TOO MANY PAGES IN JOB TO STAPLE

The job height is greater than the stapler
capacity. The height of the job to be stapled
should not exceed 50 sheets of 20-lb bond.

Verify that the job is within specifications to
be stapled. See

Supported media

on page 39

TOO MANY PAGES TO MAKE BOOKLET

The page content is too large to be saddle
stitched.

Verify that the job is within specifications to
be saddle stitched.

13.12.11 - JAM IN STAPLER

A staple jam has occurred.

Check for a jammed staple in the staple
cartridge.

13.12.21 - JAM IN LEFT ACCESSORY

13.12.22 - JAM IN LEFT ACCESSORY

13.12.23 - JAM IN LEFT ACCESSORY

A paper jam exists in the flipper assembly.

Check for jammed media in the output area
of the printer or the input area of the device.

13.12.31 - JAM IN LEFT ACCESSORY

13.12.32 - JAM IN LEFT ACCESSORY

13.12.33 - JAM IN LEFT ACCESSORY

13.12.34 - JAM IN LEFT ACCESSORY

A paper jam exists in the paper-path area.

Check for jammed media in the output area
of the printer or the input area of the device.

Chapter 3 Problem solving

ENWW

Содержание LaserJet 9040/9050 - Multifunction Printer

























































Результаты поиска

Содержание LaserJet 9040/9050 - Multifunction Printer

Отзывы:

Похожие инструкции для LaserJet 9040/9050 - Multifunction Printer

Бренды по названию

Популярные бренды

HP LaserJet 9040/9050 - Multifunction Printer, Руководство администратора

Результаты поиска

Содержание LaserJet 9040/9050 - Multifunction Printer

Отзывы:

Похожие инструкции для LaserJet 9040/9050 - Multifunction Printer

Бренды по названию

Популярные бренды