manualshive.com logo in svg

HP E3491A, Инструкция по установке и обслуживанию

Поделиться
Скачать
HP E3491A Скачать руководство пользователя страница 30

Connecting to a Target System

The E3491A Pentium Probe can be connected to a target system by
the methods listed below.

•

Directly through the Intel defined 20- or 30-pin debug connector.

•

Through the HP E2457A Pentium Preprocessor Interface.

•

Through a custom designed interface.

This chapter describes the procedures to connect to the Intel defined
debug connectors and the E2457A Pentium preprocessor. To design a
custom interface refer to chapter 3 "Designing a target system for use
with the Intel-defined debug interface." 

Connectors provided

The following components are provided with the E3491A Pentium probe for
the purpose of testing the probe and connecting to a target system.

•

A 20-conductor cable assembly (HP part number E3491-61601)

•

A 30-conductor cable assembly (HP part number E3491-61602)

•

An adapter board (HP part number E2491-66503)

•

A 2-conductor cable assembly with  SMT Grabbers (HP part number
64762-61602)

•

A self-test connector (HP part number E3490-61604) 

Connecting to the Target System 

Connectors provided

22

Содержание E3491A







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды