manualshive.com logo in svg

HP E3491A, Инструкция по установке и обслуживанию

Поделиться
Скачать
HP E3491A Скачать руководство пользователя страница 25

To verify serial communications 

1

Start a terminal emulator program on the host computer.

If you are using a PC, the Terminal application in Microsoft Windows will
work fine.

If you are using a UNIX workstation, you can use a terminal emulator such as
cu or kermit.

2

Plug the power cord into the HP E3491A Pentium Probe.

When the HP E3491A Pentium Probe powers up, it sends a message (similar
to the one that follows) to the serial port and then displays a prompt:

                  Copyright (c) Hewlett-Packard Co. 1987

All Rights Reserved.  Reproduction, adaptation, or translation without prior

written permission is prohibited, except as allowed under copyright laws.

  HPE3499A Series Emulation System

    Version:   A.05.00 19Jan95 17:01 Proto 

    Location:  Generics

 HPE3491A Pentium (tm)Processor Probe Emulator

    Version:   A.01.00 05Jan95 12:22 Proto 

R>

The version numbers may be different for your HP E3491A Pentium Probe.

3

Press the Return or Enter key a few times.

You should see a prompt such as "R>" or "p>".

See Also

"Problems with the Serial Interface," page 46.

Setting Up a Serial Connection

To verify serial communications 

17

Содержание E3491A







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды