manualshive.com logo in svg

HP E1330A, Руководство по обслуживанию

Поделиться
Скачать
HP E1330A Скачать руководство пользователя страница 34

Repair Strategy

Hewlett-Packard recommends replacement of the entire assembly in the
event of a failure. Procedures in this chapter describe troubleshooting
techniques.

Troubleshooting
Techniques

To troubleshoot an HP E1330A/B module problem you must first identify
the problem and then isolate the cause of the problem to a replaceable
assembly. See Chapter 3 — Replaceable Parts for descriptions and
locations of HP E1330A/B replaceable parts.

Identifying the

Problem

Table 4-1 lists some common problems for the HP E1330A/B modules,
along with symptoms and possible solutions. If the problem cannot be
identified using these steps, replace the assembly.

  Table 4-1. HP E1330A/B Typical Problems

Symptom

Possible Solutions

Non-zero error code in
response to SYST:ERR?

See Appendix A of the 

HP E1330A/B

Quad 8-Bit Digital I/O Module User’s
Manual

.

Module not responding to
commands.

See “Making Visual Checks” in this
chapter.

Module fails Digital Test
(Test 2-1).

See “Testing the Module” in this
chapter.

Making Visual

Checks

Visual checks for the HP E1330A/B modules include the following. See
Table 4-2 for typical checks.

•

Check switches/jumpers

•

Check for heat damage

•

Check connector contacts

NOTE

See the HP E1330A/B Quad 8-Bit Digital I/O Module User’s Manual  for
information on logical address and IRQ settings.  If there are no apparent
problems following the visual checks, run the Performance Verification
Tests in Chapter 2 to see if the module is defective.

34 Service

Chapter 

4

Содержание E1330A









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды