HP Compaq dx7300 Скачать руководство пользователя

Страница: 174 / 234

C–4

433611-001

Service Reference Guide, dx7730

POST Error Messages

511-CPU, CPUA, or

CPUB Fan not detected

CPU fan is not connected

or may have

malfunctioned.

1. Reseat the CPU fan.

2. Reseat fan cable.
3. Replace the CPU fan.

512-Chassis, rear

chassis, or front chassis

fan not detected

Chassis, rear chassis, or

front chassis fan is not

connected or may have

malfunctioned.

1. Reseat chassis, rear chassis, or front

chassis fan.

2. Reseat fan cable.
3. Replace chassis, rear chassis, or

front chassis fan.

514-CPU or Chassis Fan

not detected.

CPU or chassis fan is not

connected or may have

malfunctioned.

1. Reseat CPU or chassis fan.

2. Reseat fan cable.
3. Replace CPU or chassis fan.

601-Diskette Controller

Error

Diskette controller

circuitry or floppy drive

circuitry incorrect.

1. Run Computer Setup (F10 Setup).

2. Check and/or replace cables.
3. Clear CMOS.

4. Replace diskette drive.

5. Replace the system board.

605-Diskette Drive Type

Error

Mismatch in drive type.

1. Run Computer Setup (F10 Setup).

2. Disconnect any other diskette

controller devices (tape drives).

3. Clear CMOS.

610-External Storage

Device Failure

External tape drive not

connected.

Reinstall tape drive or press

and

allow system to reconfigure without the

drive.

611-Primary Floppy Port

Address Assignment

Conflict

Configuration error.

Run Computer Setup and check the

configuration in

Advanced >

Onboard Devices

660-Display cache is

detected unreliable

Integrated graphics

controller display cache

is not working properly

and will be disabled.

Replace system board if minimal

graphics degrading is an issue.

912-Computer Cover

Has Been Removed

Since Last System Start

Computer cover was

removed since the last

system startup.

No action required.

917-Front Audio not

Connected

Front audio harness has

been detached or

unseated from the system

board.

Reconnect or replace front audio

harness.

POST Error Messages

(Continued)

Screen Message

Probable Cause

Recommended Action

Содержание Compaq dx7300











































































































































































































































Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды

HP Compaq dx7300, Справочное руководство

Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды