background image

Service Reference Guide, dx7300

433611-001

F–1

F

Memory

The dx7300 and dc7700 series computers with Intel-based processors come with double data rate 
2 synchronous dynamic random access memory (DDR2-SDRAM) dual inline memory modules 
(DIMMs). 

Ä

CAUTION: 

DDR and DDR2 memory modules are not interchangeable.

DDR2-SDRAM DIMMs 

The memory sockets on the system board can be populated with up to four industry-standard 
DIMMs. These memory module sockets are populated with at least one preinstalled memory 
module. To achieve the maximum memory support, you can populate the system board with up 
to 8GB of memory configured in a high-performing dual channel mode.

For proper system operation, the DDR2-SDRAM DIMMs must be:

industry-standard 240-pin

unbuffered PC2-4300 533 MHz-compliant, PC2-5300 667 MHz-compliant, or PC2-6400 
800 MHz-compliant

1.8volt DDR2-SDRAM DIMMs

The DDR2-SDRAM DIMMs must also:

support CAS latency 4 (DDR2/533 MHz and DDR2/667 MHz) and CAS latency 5 
(DDR2/667 MHz and DDR2/800 MHz)

contain the mandatory JEDEC SPD information

In addition, the computer supports:

256Mbit, 512Mbit, AND 1 Gbit non-ECC memory technologies

single-sided and double-sided DIMMS 

DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM 
are not supported

The system will not start if you install unsupported DIMMs.

DIMM Sockets

There are four DIMM sockets on the system board, with two sockets per channel. The sockets are 
labeled XMM1, XMM2, XMM3, and XMM4. Sockets XMM1 and XMM2 operate in memory 
channel A. Sockets XMM3 and XMM4 operate in memory channel B.

Содержание Compaq dx7300











































































































































































































































Отзывы: