HP Compaq dx7300 Скачать руководство пользователя

Страница: 143 / 234

Service Reference Guide, dx7300

433611-001

7–37

Removal and Replacement Procedures— Slim Tower (ST) Chassis

3. If reusing the existing heatsink, clean the bottom of the heatsink with the alcohol pad

provided in the spares kit.

CAUTION:

Before reinstalling the heatsink you must clean the top of the processor and the bottom of the

heatsink with an alcohol pad supplied in the spares kit. After the alcohol has evaporated, apply thermal

grease to the top of the processor from the syringe supplied in the spares kit.

4. Apply the thermal grease provided in the spares kit to the top of the processor and install the

heatsink atop the processor.

5. Go to step 7.

6. If using a new heatsink, remove the protective covering from the bottom of the heatsink and

place it in position atop the processor.

7. Secure the heatsink to the system board and system board tray with the 4 captive screws and

attach the heatsink control cable to the system board.

CAUTION:

Heatsink retaining screws should be tightened in diagonally opposite pairs (as in an X) to

evenly seat the heatsink on the processor. This is especially important as the pins on the socket are very

fragile and any damage to them may require replacing the system board.

✎

After installing a new processor onto the system board, always update the system ROM to ensure
that the latest version of the BIOS is being used on the computer. The latest system BIOS can be
found on the Web at:

http:\\h18000.www1.hp.com/support/files

Содержание Compaq dx7300











































































































































































































































Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды

HP Compaq dx7300, Справочное руководство

Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды