HP Compaq dx7300 страница 193 Скачать руководство пользователя

Страница: 193 / 234

Service Reference Guide, dx7300

433611-001

D–9

Troubleshooting Without Diagnostics

Solving Hard Drive Problems

Problem

Cause

Solution

Hard drive error occurs.

Hard disk has bad

sectors or has failed.

Use a utility to locate and block

usage of bad sectors. If necessary,

reformat the hard disk.
In Windows XP, right-click

Start

click

Explore

, and select a drive.

Select

File > Properties > Tools

Under

Error-checking

, click

Check Now

Disk transaction problem.

Either the directory

structure is bad or there

is a problem with a file.

In Windows XP, right-click

Start

click

Explore

, and select a drive.

Select

File > Properties > Tools

Under

Error-checking

, click

Check Now

Drive not found (identified).

Cable could be loose.

Check cable connections.

The system may not

have automatically

recognized a newly

installed device.

1. See reconfiguration directions in

the Solving Hardware

Installation Problems section. If

the system still does not

recognize the new device,

check to see if the device is

listed within Computer Setup. If

it is listed, the probable cause is

a driver problem. If it is not

listed, the probable cause is a

hardware problem.

2. If this is a newly installed drive,

enter Setup and try adding a

POST delay under

Advanced

> Power-On

The device is attached

to a SATA port that has

been disabled in

Computer Setup.

Run Computer Setup and ensure the

device’s SATA port is enabled in

Storage > Storage Options

Drive responds slowly

immediately after

power-up.

Run Computer Setup and increase

the POST Delay in

Advanced >

Power-On Options

Nonsystem disk/NTLDR

missing message

System is trying to start

from a non bootable

diskette.

Remove the diskette from the diskette

drive.

Содержание Compaq dx7300











































































































































































































































Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды

HP Compaq dx7300, Справочное руководство

Результаты поиска

Содержание Compaq dx7300

Отзывы:

Похожие инструкции для Compaq dx7300

Бренды по названию

Популярные бренды