HP BladeSystem c3000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 108

background image

HP BladeSystem Insight Display troubleshooting 19

Symptoms: HP BladeSystem c7000 Enclosure Insight Display

Symptoms

Initial step

Required steps

The display screen is off, and the buttons

do not operate.

Press any Insight Display button to try to
wake up the display. The Insight Display

powers on automatically if the health is
good.

Begin with step 1.

The display screen flashes, and the Insight

Display buttons do not operate.

Press any Insight Display button to stop the
flashing. The Insight Display flashes when

any of the following are true:

•

After inactivity if the health is degraded

or failed

•

The UID is on

•

A chat message has been sent to the

enclosure

Begin with step 1.

Procedures: HP BladeSystem c7000 Enclosure Insight Display

CAUTION:

Some troubleshooting procedures require powering down an entire enclosure. To

avoid possible data loss, always secure permission before powering down an enclosure.

CAUTION:

If you are using a Virtual Connect environment, some of these procedures might

cause the loss of Virtual Connect credentials and the loss of communication between the Onboard

Administrator and the Virtual Connect Interconnect module. Ensure the Virtual Connect
configuration is backed up before proceeding with any of the following procedures. Virtual
Connect configuration can be backed up by using Virtual Connect GUI or Virtual Connect

Support Utility.

CAUTION:

To avoid data loss, do not remove an Onboard Administrator when the Insight

Display shows a firmware update in progress. During this activity, the Insight Display displays the
Firmware Update screen with the Lock icon and the firmware update progress bar.

For the steps in this table, use the following definitions for all variables:

•

Standby Onboard Administrator = Suspect OA #Y

•

Y = Original bay location for the standby module

•

Second module = Suspect OA #X

•

X = Original bay location of the active module

Step

HP BladeSystem c7000 Enclosure Insight Display action and verification

Step 1

Action

Check the Onboard Administrator health LED.

Verification

If the Onboard Administrator health LED is on, then continue to the next step.
If the Onboard Administrator health LED is off, then perform the following substeps:

1

Check the power to the enclosure.

2

Be sure that the power supplies are installed and are operating properly.

3

Complete step 1 again.

«
...
17
18
19
20
21
...
»

Содержание BladeSystem c3000













































































































Отзывы:

Нет отзывов

Похожие инструкции для BladeSystem c3000

Бренд: National Instruments Страницы: 65

Бренд: CommScope Страницы: 11

Бренд: Racal Instruments Страницы: 170

CRS-1 - Carrier Routing System Router

Бренд: Cisco Страницы: 104

Бренд: Wesena Страницы: 12

Бренд: nMedia Страницы: 4

Бренд: nMedia Страницы: 4

Бренд: nMedia Страницы: 7

Бренд: nMedia Страницы: 8

Бренд: nMedia Страницы: 9

Бренд: Lindy Страницы: 20

Бренд: Fortinet Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды