HP 3100 v2 Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 239

background image

38

Description

Use

virtual-cable-test

to test the cable connection of an Ethernet interface. The test results are

displayed within five seconds.

The following cable states are available:

•

Normal—The cable is in good condition.

•

Abnormal—Any fault other than a short or open circuit is detected.

If the cable connection is normal, the displayed cable length is the total length of the cable.

If the cable connection has a fault, it is the length from the local port to the faulty point.

If the link of an Ethernet interface is up, testing its cable connection will cause the link to go down and
then up.

The test result is for reference only. The cable length detection error is up to 5 m (about 16 ft). If a test
item is not available, a hyphen (-) is displayed.

NOTE:

Fiber ports do not support this command.

Examples

# Test the cable connection of Ethernet 1/0/1.

<Sysname> system-view

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] virtual-cable-test

Cable status: normal, 1 metres

Pair Impedance mismatch: -

Pair skew: - ns

Pair swap: -

Pair polarity: -

Insertion loss: - db

Return loss: - db

Near-end crosstalk: - db

NOTE:

The

Pair Impedance mismatch

field has the following values:

•

Yes

—Match

•

No

—Mismatch

«
...
43
44
45
46
47
...
»

Содержание 3100 v2 Series
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3100 v2 Series

Бренд: 3Com Страницы: 128

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 422

3CR16708-91 - OfficeConnect Managed Switch 9

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 30

Бренд: 3Com Страницы: 36

Бренд: 3Com Страницы: 4

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 77

Бренд: 3Com Страницы: 570

OfficeConnect WX1200

Бренд: 3Com Страницы: 28

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 4

CoreBuilder 6000

Бренд: 3Com Страницы: 31

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

852-112/000-001

Бренд: WAGO Страницы: 30

Бренд: EtherWAN Страницы: 2

Link Power LPS2400-T1

Бренд: Inscape Data Страницы: 8

Бренд: Watchguard Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды