HP 3100 v2 Series Скачать руководство пользователя страница 18

Страница: 18 / 239

Table 4 Description on the possible physical states of a Ethernet interface

Field Description

The interface is physically up.

DOWN

The interface is physically down, because no physical connection exists.
Possible reason: The network cable is disconnected or faulty.

DOWN ( Administratively )

The interface is physically down, because it was shut down with the

shutdown

command. To restore its physical state, use the

undo

shutdown

command.

DOWN ( Link-Aggregation
interface down )

The interface is physically down, because the aggregate interface
corresponding to the aggregation group to which it belongs was shut down
with the

shutdown

command.

DOWN ( OAM connection
failure )

The interface is physically down, because an OAM connection fails to be
established on it or the OAM connection is disconnected.

DOWN ( DLDP connection
failure )

The interface is physically down, because a DLDP connection fails to be
established on it or the DLDP connection is disconnected.

DOWN ( Loopback
detection-protected )

The interface is shut down, because a loop is detected on it.

DOWN ( BPDU-protected )

The interface is shut down by the BPDU guard function.

DOWN ( Monitor-Link uplink
down )

The interface is physically down, because the uplink of the monitor link
group to which it belongs is down.

# Display brief information about all interfaces.

<Sysname> display interface brief

The brief information of interface(s) under route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Main IP Description

NULL0 UP UP(s) --

Vlan1 UP UP 192.168.0.85

Vlan2 DOWN DOWN --

Vlan1010 DOWN DOWN --

The brief information of interface(s) under bridge mode:

Link: ADM - administratively down; Stby - standby

Speed or Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BAGG1 DOWN auto A A 1

Eth1/0/1 DOWN auto A A 1

Eth1/0/2 DOWN auto A A 1

Eth1/0/3 DOWN auto A A 1

Eth1/0/4 DOWN auto A A 1

Eth1/0/5 DOWN auto A A 1

Eth1/0/6 DOWN auto A A 1

Eth1/0/7 DOWN auto A A 1

Eth1/0/8 DOWN auto A A 1

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Похожие инструкции для 3100 v2 Series

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Похожие инструкции для 3100 v2 Series

Бренды по названию

Популярные бренды