HP 3100 v2 Series Скачать руководство пользователя страница 171

Страница: 171 / 239

164

lldp voice-vlan

Syntax

lldp voice-vlan vlan-id

undo lldp voice-vlan

View

Layer 2 Ethernet interface view, port group view

Default level

2: System level

Parameters

vlan-id

: Specifies a voice VLAN by its ID in the range of 1 to 4094.

Description

Use

lldp voice-vlan

to configure a port to advertise a specific voice VLAN ID to the connected IP

phone through LLDP. If CDP compatibility is enabled, the port sends the specified voice VLAN ID in
CDP packets to its connected IP phone.

Use

undo lldp voice-vlan

to restore the default.

By default, if a voice VLAN is configured on an LLDP-enabled port, LLDP advertises this voice VLAN
to the IP phone connected to the port.

Examples

# Configure Ethernet 1/0/1 to advertise voice VLAN 4094.

<Sysname> system-view

[Sysname] interface ethernet 1/0/1

[Sysname-Ethernet1/0/1] lldp voice-vlan 4094

voice vlan aging

Syntax

voice vlan aging minutes

undo voice vlan aging

View

System view

Default level

2: System level

Parameters

minutes

: Sets the voice VLAN aging timer, in the range of 5 to 43200 minutes.

Description

Use

voice vlan aging

to configure the voice VLAN aging timer.

Use

undo voice vlan aging

to restore the default.

By default, the voice VLAN aging timer is 1440 minutes.

In automatic voice VLAN assignment mode, the system starts the voice VLAN aging timer when
assigning the port to the voice VLAN. If no voice packets are received on the port before the timer
expires, the system removes the port from the voice VLAN.

Содержание 3100 v2 Series
















































































































































































































































Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Похожие инструкции для 3100 v2 Series

Бренды по названию

Популярные бренды

HP 3100 v2 Series, Справочник по командам

Результаты поиска

Содержание 3100 v2 Series

Отзывы:

Похожие инструкции для 3100 v2 Series

Бренды по названию

Популярные бренды