Hotsy 9450 Скачать руководство пользователя

Страница: 20 / 36

Maintenance

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

BURNER

WILL

NOT

LIGHT

Flex coupling slipping on fuel
pump shaft or burner motor shaft

Replace if needed.

On-Off switch defective

Check for electrical current reaching burner assembly
with burner switch on.

Heavy sooting on coil and burner
can cause interruption of air flow
and shorting of electrodes

Clean as required.

Improper electrode setting

Check and reset according to diagram in Operator's
Manual.

Fuel not reaching combustion
chamber

Check fuel pump for proper flow.
Check solenoid flow switch on machines with spray
gun control, for proper on-off fuel flow control.

Clogged burner nozzle

Clean as required.

Thermostat faulty or slow engine
speed

Increase engine RPM to increase voltage.

Flow switch malfunction

Remove, test for continuity and replace as needed.

Flow solenoid malfunction

Replace if needed.

Disconnected or short in electrical
wiring

All wire contacts should be clean and tight. No breaks
in wire.

Little or no fuel

Fill tank with fuel.

Improper fuel or water in fuel

Drain fuel tank and fill with proper fuel.

Clogged fuel line

Clean or replace.

Plugged fuel filter

Replace as needed.

Misadjusted burner air bands

Readjust air bands for clean burn.

Little or no fuel pressure from fuel
pump

Increase fuel pressure to specification and/or replace
fuel pump. Test with pressure gauge.

Faulty burner transformer

Test transformer for proper arc between contacts.
Replace as needed.

MACHINE

SMOKES

WHILE

BURNER UNIT

IS RUNNING

UNIT SMOKES AT

COLD-START

ONLY WHEN

BURNER

IS OFF

Improper fuel or water in fuel

Drain tank and replace contaminated fuel

Improper air adjustment

Readjust air bands on burner assembly

Fuel pressure is low <140 psi for
burner

Adjust fuel pump pressure to specifications

Burner nozzle is plugged or dirty

Replace nozzle. Check parts breakdown
for nozzle size

Burner nozzle spray pattern is faulty

Replace nozzle. Check parts breakdown
for nozzle size

Heavy accumulation of soot on coils
and burner assembly

Remove coils and burner assembly,
clean thoroughly Call local dealer

Misaligned electrode setting

Realign electrodes to specifications

Obstruction in smoke stack

Check for insulation blockage or other
foreign objects

Low engine RPM

Increase RPM to correct specs. See serial plate

Improper burner nozzle

See exploded view parts list

9450 / 9460 Operators Manual - Oil Fired 8.914-364.0 - G

Содержание 9450





































Результаты поиска

Содержание 9450

Отзывы:

Похожие инструкции для 9450

Бренды по названию

Популярные бренды

Hotsy 9450, Руководство оператора

Результаты поиска

Содержание 9450

Отзывы:

Похожие инструкции для 9450

Бренды по названию

Популярные бренды