HotSpring ARIA AR, Руководство пользователя

Страница: 8 / 44

Page 5
MoTo-MASSAge JeT
The Moto-Massage jet automatically travels up and down in a sweeping
motion, simulating the natural stroking effects of a manual massage.
The intensity of the Moto-Massage jet may be adjusted by turning the
comfort control lever.
The Moto-Massage jet has been factory adjusted to provide maximum
hydromassage, and to achieve full vertical travel with its comfort
control lever in the full air volume position. Should the Moto-Massage
®
jet not achieve full vertical travel and the problem is not a closed air
control valve or clogged filter cartridge, then your Hot Spring Service
center should be contacted.
ImporTanT: A slow or non-moving Moto-Massage jet may indicate
that the filter cartridge pores are obstructed with dirt, body oils, or
calcification. Follow the filter cartridge cleaning procedures in the Spa
care and Maintenance section of this manual.
HydRoMASSAge JeTS
The Hydromassage jets have two different nozzle options: directional
and dual port rotary. The directional nozzle allows you to aim the water
in the direction that feels best. The dual port rotary nozzle divides the
water flow into two streams, and then spins.
Turn the faceplate clockwise to increase the jet pressure and
counterclockwise to decrease the jet pressure.
aCCessory noTe: your Hot Spring
®
dealer stocks hydromassage
jet kits which can easily be installed in your spa to modify your jets from
directional to dual port rotary.
SooTHINg SeVeN
®
JeT
The Soothing Seven jet is another unique feature of Hot Spring
spas. Its seven outlets are designed to massage the muscles in the
upper back and shoulders, gently and thoroughly. Turn the faceplate
clockwise to increase the jet pressure and counterclockwise to
decrease the jet pressure. Turn the faceplate clockwise to increase the
jet pressure and counterclockwise to decrease the jet pressure.
PRecISIoN
®
JeTS
Precision jets are located above Moto-Massage
®
jets and in groups of
various sizes. They are designed to perform a soft, soothing massage
on your back and shoulders. Adjust the pressure of the Precision jets
using the comfort control
®
lever (located closest to the Precision jets).
Refer to the drawings on the following pages to familiarize yourself
with the SmartJet
®
system menus for your spa. Please note that the
SmartJet lever side of the spa is always considered the front when
referring to the locations of the different types of jets and jet systems.
The clock positions are correct when facing the spa, standing at
the smartJet lever.
JeTSTReAM
®
JeT
The JetStream jet is a large orifice hydromassage jet designed to put
maximum massaging action on a specific area of the body. It is located
in the lower part of the spa to afford optimal access for the massaging of
feet, legs, hips, and lower back. The intensity of the JetStream jets can
be altered (except the ones found in the FootWell
®
system) using the
comfort control lever. JetStream jets located in the FootWell are not
adjustable. Turn the faceplate clockwise to increase the jet pressure
and counterclockwise to decrease the jet pressure.
HydRoSTReAM
®
JeT
The Hydrostream jet is a mid-size hydromassage jet that delivers a
great massage to the feet, back and shoulder areas. Turn the faceplate
clockwise to increase the jet pressure and counterclockwise to
decrease the jet pressure.
WATeR FeATuRe
Vista ® , grandee ® , envoy ® , and Aria ® spas are equipped with a
BellaFontana
®
water feature. This water feature can be turned on or off
when the two-speed pump is on low speed (tranquil mode) or high speed.
To function correctly, the water feature on/off lever must be placed in the
full
on position only.
If the lever is not in the full on position when the pump is on high
speed, it is likely that the water feature will project water substantially
farther out into the spa as the on/off lever is opened. This is not proper
operation. If this occurs, the pump should be turned off, the water
feature lever rotated to the full on position and the pump turned on again.
CauTIon: Partial blockage of water flow at entrance of water feature
will cause the water to flow farther into or over the spa.
Vanguard
®
and Sovereign
®
models have the Soothing Stream
®
water
feature. The water feature is located on the front right corner of the spa.
A lever is used to adjust the water from full flow to completely off. The
circulation pump of the spa powers the water feature allowing the water
to run all of the time if desired. Turning the water feature lever to it’s full
clockwise position will shut the water feature off.
ImporTanT: It is recommended that the soothing stream water
feature be turned off before placing the cover onto the spa.
QUICk START-UP INSTRUCTIONS
BeFoRe you FIll youR SPA
Make sure your spa has been properly installed per all local codes, this
includes the location of the spa, the foundation of the spa as well as the
electrical installation of the spa. Installation instructions in the form of a
Pre-delivery Instruction booklet can be obtained from either your Hot
Spring dealer or online at:
www.hotspring.com/planning-tools/pre-delivery-instructions
do:
•
know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
•
Have FreshWater
®
5-way Test Strips Available.
•
Have pH/Alkalinity up & down available.
•
know the "Hardness" of your water, contact your dealer to help you
with this information. See Water Quality and Maintenance for more
information.
ImporTanT: Watkins Manufacturing corporation does not
recommend that the spa be filled with “softened” water, as this may
damage the spa’s equipment.
•
Purchase the cleanScreen
®
pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
don'T:
•
Power up the spa until it has been filled with water! Power to the
spa automatically activates critical components within the spa, such
as controls, heater, circulation pump, and other systems. If power
is supplied to these components prior to the spa being filled, the
components will be damaged, and this may result in a non-warranty
component failure.
•
Fill the spa with hot water or cold water with cold water temperature
below 50º F (10º c)! Tripping of the high-limit thermostat may result
causing your spa to stop functioning.
Getting Started