background image

31 of 39

Indesit

 

Company

Service Manual UK

English

Q

Door Hinge

1.

Remove the front panel and both side panels.

2.

Partially open the door 
(half way).

Insert a sturdy pin (or 
pop rivet etc.) in the 
hinge hole (in both Left 
and Right hinges) to 
keep the door half 
open.

Note 1: IT IS IMPERATIVE THIS IS DONE BEFORE ANY FIXINGS ARE REMOVED.

Note 2:
New hinges are supplied 
with a Temporary
Locking Pin.
DO NOT REMOVE these 
pins until after full
re-assembly.

3.

Using pliers take off the tie rod, turning it around its fastening.

4.

Disconnect the Earth Tags (Fastons) located on the hinges.

5.

Remove 4 screws (2 in each side) fixing the inner door and pull out.

6.

Pull the inner door upwards.

7.

Remove the screws

**

 located on the inner part of the dishwasher, fixing the hinges to the wash tank. 

**Note:

 One screw each side.

8.

Remove 4 screws - 2 per hinge - at the 
base of the dishwasher. 

9.

Fit the new hinges in reverse order. 
Also refit both Earth Tags and make 
sure they are secure.
The final action is to remove both 

Temporary Locking Pins

 as shown in 

(2) above.

continued...

Each NEW hinge is locked in position 
by a temporary pin. DO NOT REMOVE 
until BOTH hinges are fixed to the
Door and Dishwasher body.

Remove
2 screws 
each side

Содержание FDYF11011G








































Отзывы: