background image

12 of 39

Service Manual UK

Indesit

 

Company

English

CONSOLE PANEL

The following information is displayed during a cycle.

> Estimated Programme duration time 

This will countdown as the cycle progresses, and the time to finish will automatically update as the 
programme progresses.
The first programme displayed will 

always

 be the most commonly used programme.

This is not a countdown timer

but an estimate time

 to the end of the cycle.

If an Option as been selected a bar will illuminate above the Option button.
Fault Codes will display in the event of a machine failure - for example:

  F 6

Other information messages will scroll across the Display.

ON-OFF/RESET BUTTON

Press this button to switch the appliance on.
To Re-set a programme that requires cancelling press and hold down the On-Off button.

ON-OFF INDICATOR LAMP

This Lamp shows that the Dishwasher is Switched on.

Display

Wash cycle

Wash cycle

Half Load indicator light

Low Rinse Aid indicator light

Low Salt indicator light

Blocked Filter indicator light

Extra Drying indicator light

Multi-Functional Tablets indicator light (Tabs)

Washing and Drying indicator lights

Tap Shut-Off indicator light

Delayed Start 
indicator light

Remaining Time indicator

Short Time option indicator light

Control Panel

Start/Pause button 
and indicator lights

On-Off/Reset button 

and indicator light

Extra Drying option button

Half Load option button

Delayed Start buttons

Multi-functional Tablets 

option button (Tabs)

Display

Wash-Cycle Selection buttons

Short Time option button

Wash-Cycle Selection buttons

***

Only in completely built-in models

*

Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Содержание FDYF11011G








































Отзывы: