HOSSEVEN KH.2545, Инструкция по эксплуатации

Страница: 9 / 20

LIGHTING
To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to know the following
information:
• the construction materials of the involved products are not homogeneous, in fact there are simultaneously parts in cast iro n, steel,
refractory material and majolica;
• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable temperatures wi thin
the range of 300 ° C - 500 ° C are detected;
• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to cycl es of intense
use or of absolute standstill when season changes;
• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all materials and paint s to
complete the various elastic stresses;
• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress, as well as of wet
paint. This paint, although during the manufacture it is backed at 250 ° C for some hours, must exceed many times and for a given
period of time the temperature of 350 ° C before becoming completely embedded in the metallic surfaces.
ENgLIsH
Therefore, it is extremely relevant to take these easy steps during the lighting:
1. Make sure that a strong air change is assured in the room where the appliance is installed.
2. During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the instructions
manual) and keep the product continuously ON for at least 6-10 hours with the registers less open than the value indicated in the
instructions manual.
3. Repeat this operation for at least 4-5 or more times, according to your possibilities.
4. Then load more and more fuel (following in any case the provisions contained in the installation booklet concerning maximum
load) and, if possible, keep the lighting periods long avoiding, at least in this initial phase, short ON/OFF cycles.
5. During the first starts, no object should be leaned on the appliance and in detail on enameled surfaces. Enameled
surfaces must not be touched during heating
.
6. Once the «break - in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt heating with
excessive loads.
To light the fire, it is suggested to use small wood pieces together with paper or other traded lighting means.
The openings for air (primary and secondary) must be opened together (you must open the eventual Ignition control, and butter
fly
valve placed on the pipe of smokes exhaust). When the wood starts burning, you may load other fuels and adjust the air for
combustion according to the instructions on paragraph TECHNICAL DESCRIPTION.
Please always be present during this phase .
LOW EMISSION fire lighting
Smokeless combustion is a way of lighting a fire able to signifcantly reduce the emission of harmful substances. The wood burns
gradually from the top downwards, so combustion is slower and more controlled. Burnt gases pass through the high temperatures of
the flame and therefore burn almost completely.
Place the logs in the hearth a certain distance apart. Arrange the largest at the bottom and the smallest at the top, or vertically in the
case of tall narrow combustion chambers. Place the fire starter module on top of the pile, arranging the first logs in the module at
right angles to the pile of wood.
Fire STARTER MODULE. This fire starter module replaces a paper or cardboard starter. Prepare four logs, 20 cm long with a cross
section of 3 cm by 3 cm. Cross the four logs and place them on top of the pile of wood at right angles, with the fire lighter (wax
impregnated wood fbre for example) in the middle. The fire can be lit with a match.
If you want, you can use thinner pieces of wood. In this case, you will need a larger quantity.
Keep the flue gas exhaust valve and combustion air regulator open.
After lighting the fire, leave the combustion air regulator open in the position shown in according to the instructions on paragraph
TECHNICAL DESCRIPTION
9
WARNING: After the first ignition you can smell bad odours (owing to the drying of the glue used in the
garnitures or of the paint) which disappear after a brief using of the appliance. It must be ensured, in any case,
a good ventilation of the environment. Upon the first ignition we suggest loading a reduced quantity of fuel
and slightly increasing the calorific value of the equipment. It is FORBIDDEN to use any liquid substance as for
ex. alcohol, gasoline, oil and similar. Never switch on the device when there are combustible gases in the
room.
!
Never overload the appliance (see cap. TECHNICAL DESCRIPTION / hourly consumption). Too much fuel
and too much air for combustion can cause overheating and therefore damage the appliance. The
warranty does not cover the damages due to overheating of the equipment.
!