Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 63

Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 37

37

Heat Shield

Support Clip (C)

Support Clip (B)

Support Clip (A)

Evaporator
Bracket

F. Removal and Replacement of Heat Shield on FH2-SSB(-HD)

The heat shield was added to the evaporator assembly at auxiliary code M6. To replace
the shield, follow the instructions below.

1) Remove the original heat shield by lifting the evaporator up and sliding the heat shield

out.

) Install the new heat shield in the rotocast drain pan.
3) Slide the clips onto the end plate on the evaporator. Install the two Support Clip (C)

clips onto the hairpin end of the evaporator as shown in the illustration.

4) Install Support Clip (A) and Support Clip (B) onto the return bend end (same side as

inlet and outlet tubes) as shown in the illustration.

Note: All clips are shown in the illustration in the correct orientation for installation. Slide

the parts onto the evaporator brackets using the tabs on the support clips.

G. Removal and Replacement of Door Gasket

Remove old gasket by pulling it directly out of the vinyl gasket retainer. Thoroughly clean
the gasket area with mild soap and water prior to installing the new gasket. The new
gasket should be installed by assembling it at the corners first, then working toward the
center at the top, bottom and sides. The arrow-shaped portion of the gasket should be
firmly seated in the retainer groove for proper assembly. This can be checked by lifting
the edge of the gasket and observing the engagement.

CAUTION

In order to get a proper gasket fit, it is important not to stretch gasket material
during assembly.

«
...
35
36
37
38
39
...
»

Содержание TempGuard FH1-SSB
































































Отзывы:

Нет отзывов