Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 29

Страница: 29 / 63

Problem

Possible Cause

Remedy

[9] Defrost cycle

lasts too long.

a) Defrost Thermistor

1. Defective.

1. Replace.

b) Control Board

1. Defective.

1. Replace.

c) Defrost

1. Not enough defrosts

occurring per day. Operation
in humid conditions.

Freezer:

See "D.1.b) Defrost

Frequency."

Refrigerator:

See "D.1.b)

Defrost Frequency."

3. Check thermistor reading and

position.

d) Defrost Heaters

1. Defective. (E3 should be

displayed)

Freezer:

Replace heaters.

Reset E3 by pressing control
board "ALARM RESET."

e) Safety Defrost

Thermostat

1. Defective, turning off heaters

prematurely, or fused open.
(E3 should be displayed)

1. Freezer: Replace safety defrost

thermostat.
Reset E3 by pressing control
board "ALARM RESET."

[10] Condensate

water overflow.

a) Cabinet Contents

1. Loading of large volumes

of warm, moist, uncovered
product.

1. Cover product with plastic wrap.

b) Location of Unit

1. Unit located near high

humidity source such as
fryer, steamer, etc.

1. Relocate.

c) Seals

1. Poor sealing around

evaporator, door gaskets.

1. Adjust or replace.

d) Environment

1. Extreme environment and

door-opening conditions.

1. Adjust conditions.

[11] Abnormal
noise

a) Fasteners

1. Loose fasteners allow

vibration of part.

1. Tighten fasteners.

b) Compressor

1. Problem with mount.

1. Properly mount compressor.

Replace any missing grommets.

. Floodback to compressor.

. Check for signs of floodback

to compressor. Evacuate and
recharge if necessary.

3. Defective.

3. Replace.

c) Fan

1. Fan blade loose.

1. Adjust and tighten.

. Defective motor.

. Replace.

d) Relay

1. Chattering.

1. Replace.

Содержание TempGuard FH1-SSB
































































Результаты поиска

Содержание TempGuard FH1-SSB

Отзывы:

Hoshizaki TempGuard FH1-SSB, Руководство по обслуживанию, Страница: 29 / 63

Результаты поиска

Содержание TempGuard FH1-SSB

Отзывы: