Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 28

Страница: 28 / 63

Problem

Possible Cause

Remedy

[4] Cabinet inside

temperature too
high;
compressor will
not start.

a) Thermistor

1. Defective.

1. Check and replace.

b) Compressor Relay

1. Defective. (LED 4 is ON.

115V to relay coil.)

1. Check and replace.

c) Circuit Board

1. Defective. (LED 4 is OFF.

Compressor relay coil not
energized at 115V.)

1. Replace.

[5] Cabinet

temperature too
high.

a) Setpoint

1. Incorrect.

1. Correct setpoint.

Factory defaults:
Freezer -3°F
Refrigerator 36°F

b) Door

1. Not sealing, or open for long

intervals.

1. Check for sealing, check for door

open at time of warm cabinet
temperature.

c) Defrost

1. Not enough defrosts

occurring per day. Operation
in humid conditions.

Freezer:

See "D.1.b) Defrost

Frequency."

Refrigerator:

See "D.1.b)

Defrost Frequency."

3. Check thermistor reading and

position.

d) Refrigerant

1. Leak.

1. Repair leak and recharge.

e) Fan Motor

1. Defective.

1. Check and replace.

f) Air Filter

1. Clogged.

1. Clean.

g) Condenser

1. Dirty.

1. Clean.

h) Thermistor

1. Defective.

1. Check and replace.

i) Control Board

1. Defective.

1. Replace.

[6] Cabinet

temperature
display
indicator does
not illuminate
properly.

a) Board Connection

1. Bad connection between

control board and display
board.

1. Check connection.

b) Display Board

1. Defective.

1. Replace.

c) Control Board

1. Defective.

1. Replace.

[7] Cabinet inside

temperature too
low.

a) Thermistor

1. Defective.

1. Check and replace.

b) Compressor Relay

1. Defective; contacts welded.

1. Replace.

c) Circuit Board

1. Defective.

1. Replace.

[8] Evaporator does

not defrost
completely.

a) Defrost Thermistor

1. Defective.

1. Check and replace.

b) Defrost

1. Not enough defrosts

occurring per day. Operation
in humid conditions.

Freezer:

See "D.1.b) Defrost

Frequency."

Refrigerator:

See "D.1.b)

Defrost Frequency."

3. Check thermistor reading and

position.

c) Defrost Heaters

1. Defective. (E3 should be

displayed)

Freezer:

Replace heaters.

Reset E3 by pressing control
board "ALARM RESET."

d) Safety Defrost

Thermostat

1. Defective, turning off heaters

prematurely, or fused open.
(E3 should be displayed)

Freezer:

Replace safety defrost

thermostat.
Reset E3 by pressing control
board "ALARM RESET."

Содержание TempGuard FH1-SSB
































































Результаты поиска

Содержание TempGuard FH1-SSB

Отзывы:

Hoshizaki TempGuard FH1-SSB, Руководство по обслуживанию, Страница: 28 / 63

Результаты поиска

Содержание TempGuard FH1-SSB

Отзывы: