Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 63

Hoshizaki TempGuard FH1-SSB Скачать руководство пользователя страница 26

6

Alarm Signals

Alarm Code

Alarm

Sound Problem

Reset Options

E8

Constant
buzzer

Cabinet Temperature Sensor Malfunction
Alarm

Cabinet temperature sensor has failed.

After replacing sensor, alarm will reset.

During alarm, press "RESET" to silence
buzzer for 5 minutes.

E9

Constant
buzzer

Defrost Temperature Sensor Malfunction
Alarm

Defrost temperature sensor has failed.

After replacing sensor, alarm will reset.

During alarm, press "RESET" to silence
buzzer for 5 minutes.

E10

[Duel Temp

Models Only]

10 beeps
every ten
seconds

Communication Alarm

Freezer and refrigerator boards not
communicating properly to control
compressor delay.

When communication is restored, alarm will
reset.
During alarm, press "RESET" to silence
buzzer for 18 hours.

CF

1 beep
every ten
seconds

Clogged Filter Alarm

Condenser filter needs cleaning.

Clean filter. Allow time for sensor to react,
then press "RESET."

During alarm, press "RESET" to silence
buzzer for hours.

If this alarm occurs frequently, discharge
temperature is consistently too high.
Failure to take action could result in
damage to the compressor.

door

[Except Glass

Door Models]

beeps
every ten
seconds

Display Only: Door open.
Both Display and Beeps: Door open longer
than 3 minutes.

Close door. During alarm, press "RESET" to
silence buzzer for 3 minutes.

Note: Moving the diagnostic menu item 3 to "ON" resets all alarms regardless of

whether or not the setpoints are reached. This is a complete clearing of all
alarms. See "II.D.. Diagnostics Menu" for details.

F. Compressor Protector

When a combined temperature/amperage value is above the limit specified by the
compressor manufacturer, a protector will operate independently, turning off the
compressor. The compressor will restart when this protector has reset.

Note:

1. Compressor protector resets automatically.
. If the condenser fan is operating and the compressor is off, it is most likely that the

protector has operated.

G. Perimeter Frame Heater

This unit is equipped with a perimeter frame heater. This prevents the formation of
condensate on the front frame of the unit under high humidity conditions. If operating the
unit under conditions where condensate will not form, these heaters may be turned off
using the switch on the control box.

H. Glass Door Heater

Glass door units are equipped with a door heater. This prevents the formation of
condensate on the glass under high humidity conditions. If operating unit under
conditions where condensate will not form, these heaters may be turned off using the
switch on the control panel.

«
...
24
25
26
27
28
...
»

Содержание TempGuard FH1-SSB
































































Отзывы:

Нет отзывов