Hoshizaki KM-600MAH Скачать руководство пользователя | Manualshive

Страница: 11 / 32

background image

11

II. Installation and Operating Instructions

WARNING

1. This icemaker must be installed in accordance with applicable national, state,

and local regulations.

2.

CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews

are securely in place after installation. Make sure that none have fallen into
the storage bin.

A. Checks Before Installation

• Visually inspect the exterior of the shipping container and immediately report any

damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.

• Remove the shipping carton, tape, and packing material. If any are left in the icemaker,

it will not work properly.

• Remove the panels to prevent damage when installing the icemaker. See "II.B. How to

Remove Panels."

• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the icemaker is exposed to the

sun or to heat, remove the film after the icemaker cools.

• Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the

fan blade (if applicable) turns freely.

• Check that the compressor is snug on all mounting pads.
• See the nameplate on the rear panel, and check that your voltage supplied

corresponds with the voltage specified on the nameplate.

• This icemaker can be installed on a storage bin 22" wide or wider. Hoshizaki Ice

Storage Bin, Model B-300 series is recommended. For further options, contact your
local Hoshizaki distributor.

• On remote air-cooled model, a remote condenser unit is needed. Hoshizaki Remote

Condenser Unit, Model URC-6F, is recommended.

B. How to Remove Panels

See Fig. 1

• Front Panel: Remove the screw. Lift up and

towards you.

• Top Panel: Lift up at front slightly, push rearward,

and lift off.

• Side Panel (R): Remove the screw. Slide forward

slightly, and lift off.

• Insulation Panel: Lift up slightly, and pull towards

you.

• Base Cover: Lift up slightly, and pull towards you.

Fig. 1

Top Panel

Front
Panel

Insulation
Panel

Side Panel (R)

Base Cover

Screw

Screw

«
...
9
10
11
12
13
...
»

Содержание KM-600MAH

































Отзывы:

Нет отзывов

Похожие инструкции для KM-600MAH

the Barista Pro BES878

Бренд: Sage Страницы: 28

Barista Express BES875

Бренд: Sage Страницы: 36

Бренд: Gastroback Страницы: 28

Бренд: Faema Страницы: 46

Kikko Max P250U00

Бренд: Necta Страницы: 36

LabelManager 360D

Бренд: Dymo Страницы: 30

Бренд: Davis & Waddell Страницы: 3

Home Bakery Supreme BB-CEC20

Бренд: Zojirushi Страницы: 16

Kitchen Pro K6744

Бренд: Regal Страницы: 60

Бренд: Ernesto Страницы: 2

Бренд: Adkins Страницы: 31

Бренд: Mellerware Страницы: 12

Бренд: Klarstein Страницы: 44

Бренд: Moulinex Страницы: 56

Бренд: Frigidaire Страницы: 9

Signature PRO 2

Бренд: Flair Страницы: 2

Бренд: Brother Страницы: 16

PT-1160 Martha By Mail

Бренд: Brother Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды