background image

GENERAL PRECAUTIONS

Use only Brother TZ tapes with this machine. Do not use any other tapes.

Tapes are available in three different widths: 1/4”(6 mm), 3/8”(9 mm) and 1/2”(12 mm).

Do not pull the tape since this may damage the tape cassette.

Do not attempt to cut the tape while printing or feeding since this will damage the
tape.

Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry
cloth.

Remove the batteries and disconnect the AC adapter if you do not intend to use the
machine for an extended period of time.

Note:

If power is disconnected for more than three minutes, all text shown in the
display and any text files stored in the memory will be lost.

Do not put any foreign objects into or anything on the machine.

Do not expose the machine to high temperatures or high humidity. Never leave it on
the dashboard or in the back of your car.

Do not use the machine in dusty places, and keep it out of both direct sunlight and
rain.

Do not leave any rubber or vinyl on the machine for an extended period of time.
Doing so may cause staining.

After inserting a new tape cassette, advance the tape by holding down 

 and

pressing 

once.

Do not touch the print head mechanism. If the head is touched, clean it immediately
with a soft wipe (e.g., a cotton swab) to avoid permanent damage.

To avoid injuries, do not touch the cutter’s edge.

Use only the AC adapter designed exclusively for this machine. Use of any
other adapter will void the warranty.
Please contact your Brother dealer for details.

POWER SUPPLY

Changing the batteries

CAUTION

Batteries installed incorrectly can overheat and leak. Can result in chemical burns
and machine overheating and damage.

Your machine requires 6 alkaline AAA batteries.
Carefully follow these instructions.

1

Press bumps on top of back cover and open.

2

Pull out tape cassette, if one was installed.

3

Remove batteries, if they were already installed.

4

Hold machine as pictured:

5

Insert six new batteries as follows:

Always:

• Insert “+” ends before “-” ends.
• Remove “-” ends before “+” ends.
• Replace all 6 batteries at the same time with new ones.

6

Insert tape cassette.

7

Insert two hooks on bottom end of back cover into slots on bottom
of machine. Push down firmly on cover until it snaps into place.

8

Turn machine on.
If no power, immediately remove batteries and call Brother Customer Service at:
1-877-478-6824

Optional AC adapter

The AC adapter allows you to use this machine wherever an electrical outlet is available.
Use Brother’s AD-30 adapter for your new PT-1160.

1

Insert the plug on the adapter cord into the adapter
jack on the bottom end of the machine.

2

Insert the plug into the nearest standard electrical outlet.

OVERVIEW

  

Display

Backspace key

CURSOR MOVEMENT

You can view and edit different parts of the text by moving the cursor backward and
forward.

To move the cursor one character at a time, press 

 or 

.

To move the cursor to the beginning of the text, hold down 

 and press 

.

To move the cursor to the end of the text, hold down 

 and press 

.

BACKSPACE KEY

This key can be used to remove characters from your text, clear all of the text or cancel
functions.

To delete the character to the left of the cursor or to cancel a function (instead of

pressing 

), press 

.

To clear all of the text that is currently entered, hold down 

 and press 

.

SPACE KEY

As on a word processor, press 

 to add a blank space to your text.

RETURN KEY

Press 

 when you wish to select a setting, or end the first line of text and start the

second.

To add a second line, press 

 once. The return mark (

) appears in the text to

indicate the end of the first line and the beginning of the second.

Note:

Two lines of text can only be entered if 3/8”(9-mm) or 1/2”(12-mm)-wide tape
is installed.

To  select an item from a list, press 

 once.

ACCENTED CHARACTERS

You can also choose from a list of other accented characters that can be added to your text.

1

Press 

 if you want the accented character to be an upper case letter.

Note:

To quit the following procedure at any time without making any changes, press 

.

2

Hold down 

 and press 

. The message “A-U?” appears in the display.

3

Turn the 

Function 

dial until the cursor is positioned under the desired accented

character.

OR

Press the key for the letter in the accented character that you wish to add, and then

press 

 and 

 until the cursor is positioned under the desired accented

character.

4

Press the 

Function 

dial (or 

) to add the selected character to your text.

SYMBOLS

In addition to the letters, symbols, and numerals on and above the keys, there are 72
symbols available with the 

Symbol 

function. These symbols are divided into 10 groups,

corresponding to the letters A through I.

1

Press 

.  The message “A-I?” appears in the display.

2

Press the key for the letter of the group containing the symbol that you wish to add,

and then press 

 and 

 until the cursor is positioned under the desired symbol.

3

Press 

 to add the symbol to the text.

Return key

Num key

Function dial

Caps key

TAPE CASSETTES

A TZ tape cassette is supplied with this unit. The Brother TZ tapes used with this machine are
available in a variety of colors and three tape widths (1/4”(6 mm), 3/8”(9 mm), 1/2”(12 mm)).

1

Press in on the rough area at the top end of the machine and
fold open the back cover.

2

If a tape cassette is already installed, remove it by pulling it
straight up.

3

If the ink ribbon in the other tape cassette is loose, use your
finger to wind the toothed wheel in the direction of the arrow on
the cassette until there is no slack in the ribbon. Also, make sure
that the end of the tape feeds under the tape guides.

Note:

If you are using a new tape cassette provided with a
stopper, be sure to remove the stopper.

4

Insert the tape cassette firmly into the compartment, making
sure that the entire back of the cassette contacts the bottom of
the compartment.

Note:

When inserting a tape cassette, make sure that the inner
ribbon does not catch on the corner of the metal guide.

5

Securely close the back cover, making sure that it snaps into place.

6

Feed the tape by holding down 

 and pressing 

 once, and

then push in the tape cutter lever to cut the tape.

LETTERING STICK

The enclosed lettering stick enables you to easily remove the backing from labels printed
on laminated tapes.

1

Hold the tape in your left hand, with the printed surface facing up, and hold the stick
in your right hand.

2

Pass the tape halfway through the long narrow hole in the stick.

3

Turn the stick three-quarters of a turn towards you and pull the stick away from you
as shown below.

4

Peel off the label backing.

STARTING

Press  

. If batteries have been installed or the machine has been plugged in using the

optional AC adapter, the previous session’s information is displayed when the machine is
turned on. This feature allows you to stop work on a label and turn off the machine, then
return to it later without having to re-enter the text.
The machine automatically turns off if no key is pressed within five minutes. The current
session’s information is stored in the machine’s internal memory and displayed when the
machine is later turned on again.

CODE KEY

By holding down 

 and pressing a key with a function, character or accent written

above it, you can use the corresponding function or add the corresponding character to
your text.

CAPS KEY

By pressing 

 to enter 

Caps 

mode, you can add upper-case letters to your text by

simply pressing the character keys. When this mode is on, the 

Caps 

indicator in the top-

left corner of the display comes on. To exit 

Caps 

mode, press 

 until the 

Caps

indicator goes off.

NUM KEY

By pressing 

 to enter 

Num 

mode, you can add numbers to your text by simply

pressing the corresponding keys. When this mode is on, the 

Num 

indicator in the bottom-

left corner of the display comes on. To exit 

Num 

mode, press 

 until the 

Num 

indicator

goes off.

DISPLAY

This machine’s LCD shows one row of 8 characters; however, the text that you enter can
be up to 55 characters in length. The 8-character display is like a window which moves
across the text.

1234567890123456789012345678901234567890123456789012345

Tape cutter lever

Back cover

Batteries

Print head

On/Off key

Tape cassette

Tape exit slot

Letter

Accented character

Letter

Accented character

A

À

Á

Ä

Â

Ã

Æ

a

à

á

ä

â

ã

æ

C

Ç

c

ç

E

È

É

Ë

Ê

e

è

é

ë

ê

I

Í

Ï

Î

i

í

ï

î

N

Ñ

n

ñ

O

Ó

Ö

Ô

Õ

o

ó

ö

ô

õ

U

Ù

Ú

Ü

Û

u

ù

ú

ü

û

Group

Symbols

A

Ü

ü

Ç

ç

Æ

æ

á

é

B

í

ó

ú

Ã

ã

C

Õ

õ

Ñ

ñ

¡

¿

§

#

D

·

°

;

%

+

×

÷

=

E

$

¢

[

]

2

3

2

3

F

4

TM

®

©

G

H

I

_

~

SKU HPT003

PT-1160

USER’S GUIDE

LA6618001

Printed in China

With your ne

w PT -1160, y

ou can create labels for any application.

 Select from the many fr

ames,

character sizes and styles to design beautiful custom labels

. In addition, the v

ariety of tape car

tridges

availab

le allows y

ou to print labels with diff

erent widths and exciting colors

.

Y ou no longer ha

ve

 to worr

y about urgent tasks that require professional printing.

 The quality and

perfor

mance of the PT -1160 mak

es it an extremely pr

actical machine.

Although this machine is easy to use, w

e suggest that y

ou read this manual carefully bef

ore starting and

keep the man

ual in a handy place for future ref

erence.

FCC NOTICE

This equipment has been tested and found to comply with the limits f

or a Class B

digital device

, pursuant to Pa

rt 15 of the FCC Rules

. These limits are designed to

provide reasonab

le protection against harmful interf

erence in a residential installation.

This equipment generates

, uses, and can radiate r

adio frequency energy and, if not

installed and used in accordance with the instructions

, may cause har

mful

interference to r

adio communications

. Ho

we

ve

r, there is no guar

antee that

interference will not occur in a par

ticular installation. If this equipment does cause

harmful interf

erence to radio or tele

vision reception, which can be determined b

y

turning the equipment off and on, the user is encour

aged to try to correct the

interference b

y one or more of the f

ollowing measures:

-

Reorient or relocate the receiving antenna.

-

Increase the separation betw

een the equipment and receiver

.

-

Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

-

Consult the dealer or an exper

ienced radio/TV technician f

or help.

-

Changes or modifications not expressly appro

ved b

y Brother Industr

ies, Ltd.

could void the user’

s authority to operate the equipment.

INTRODUCTION

Patent n

umbers and patent publication n

umbers which are related to this product

are as below:

USP4839472

USP4983058

USP5120147

USP4927278

USP5009530

USP4976558

USP5069557

-

+

FIRST, in 
LOWER 

layer 

insert ˝+˝ ends 
pointing DOWN.

SECOND, in 
UPPER 

layer 

insert ˝+˝ ends 
pointing UP.

+

-

GH

AB

CD

EF

ABCDEF

Reviews: