Hoshizaki KM-600MAH Скачать руководство пользователя | Manualshive

Страница: 2 / 32

background image

2

IMPORTANT

Only qualified service technicians should install, service, or maintain this
icemaker. No installation, service, or maintenance should be undertaken
until the technician has thoroughly read this Instruction Manual. Likewise, the
owner/manager should not proceed to operate the icemaker until the installer
has instructed them on its proper operation. Failure to install, operate, and
maintain the equipment in accordance with this manual may adversely affect
safety, performance, component life, and warranty coverage.

Hoshizaki provides this manual primarily to assist qualified service technicians in the
installation, maintenance, and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, write, or send an e-mail message to the Hoshizaki Technical
Support Department for assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269

Attn: Hoshizaki Technical Support Department

Phone: 1-800-233-1940 Technical Support

(770) 487-2331

Fax: 1-800-843-1056

(770) 487-3360

E-mail: [email protected]

Web Site: www.hoshizaki.com

NOTE: To expedite assistance, all correspondence/communication MUST include the

following information:

• Model Number

• Serial Number

• Complete and detailed explanation of the problem.

«
1
2
3
4
...
»

Содержание KM-600MAH

































Отзывы:

Нет отзывов

Похожие инструкции для KM-600MAH

Бренд: Pastamaster Страницы: 26

Бренд: La Pavoni Страницы: 9

Бренд: Guzzanti Страницы: 89

Бренд: Stalgast Страницы: 8

Бренд: MAGIMIX Страницы: 54

Бренд: Netum Страницы: 18

Бренд: Schaerer Страницы: 34

NESPRESSO PIXIE M 112

Бренд: MAGIMIX Страницы: 33

NAVIGLIO HD8749/01

Бренд: Gaggia Страницы: 48

Бренд: Eldom Страницы: 34

Бренд: BIXOLON Страницы: 36

Бренд: Cuisinart Страницы: 10

Бренд: Dash Страницы: 15

Бренд: Nespresso Страницы: 44

Бренд: Concept2 Страницы: 112

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 5

Бренд: KitchenAid Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды