Hoshizaki KM-280MAH Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

background image

19

7) Fully open the Cleaning Valve on the left side wall of the machine compartment.
See Fig. 10.

IMPORTANT

1. The Cleaning Valve is used to provide access to the inside of the Evaporator
during the cleaning and sanitizing operation. It should be closed for all
icemaking operation. The Compressor will not operate unless this valve is
completely closed.

2. To open the Cleaning Valve, the Valve Handle should be parallel to the valve
body. To close the valve, the Valve Handle should be at a right angle to the
valve body.

Fig. 10

«
...
17
18
19
20
21
...
»

Содержание KM-280MAH
























Отзывы:

Нет отзывов

Похожие инструкции для KM-280MAH

Saeco Poemia HD8325/08

Бренд: Saeco Страницы: 3

Бренд: Bartscher Страницы: 25

Бренд: Dash Страницы: 17

Бренд: SEGAFREDO Страницы: 86

Arabica 10032771

Бренд: Klarstein Страницы: 44

MAXX ICE MID200 Series

Бренд: Maxx Cold Страницы: 13

Бренд: toptack Страницы: 45

49464 - Programmable Coffee Maker

Бренд: Hamilton Beach Страницы: 2

Бренд: Ice-O-Matic Страницы: 2

Бренд: Brady Страницы: 48

Бренд: Maestro Страницы: 2

Бренд: Saeco Страницы: 88

Бренд: FAP Страницы: 25

8 7121 8405 6446

Бренд: Bestron Страницы: 40

Бренд: Klarstein Страницы: 66

Бренд: Black+Decker Страницы: 28

Бренд: Black+Decker Страницы: 80

Бренд: West Bend Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды