Hoshizaki FM-300AFE-HC Скачать руководство пользователя страница 60

Страница: 60 / 69

Code

Error

Condition

Operation

Reset

Check/Repair

Frequent

Voltage Error

c3 error occurs 3 times in

24 hours.

Whole unit

stops.

Press Reset

Button.

Supply voltage

Gear Motor

Failure

Precaution

Ed and EE occur 10 times
in total.

EJ blinks.

N/A

Replace Evaporator

and Gear Motor.

Bin Control

Switch Error

Bin Control Protective

Switch trips.

Whole unit

stops.

Press Reset

Button.

Bin Control Switch

Low Voltage

Sensing

Transformer

Circuit Open

Low Voltage Sensing

Transformer circuit is open.

Whole unit

stops.

Press Reset

Button.

Low Voltage Sensing
Transformer

No model setting.

Controller

Board Model

Setting Error

Unacceptable supply

frequency.

Whole unit

stops.

Press Reset

Button.

Model setting, Supply
frequency

Controller Board
Error

Controller Board IC fails.

Whole unit
stops.

Press Reset
Button.

Replace Controller
Board.

None

Electric Leak
Short Circuit

Electric leak or
overcurrent.

Whole unit
stops.

Press Reset
Button.
Replace
Fuse.

Electric leak, Fuse

Non-Interlock Errors

Code

Error

Condition

Operation

Reset

Check/Repair

Time

“

— —

”

Microcomputer
Read/Write
Error

Microcomputer fails to
read/write properly.

Memory circuit
not available.

Replace
Controller
Board.

Error records and
compressor
operating hours not
available on
display

Low Water

Water supply
continues for more
than 90 seconds, or
Float Switch trips at
lower float level and
does not reset for
more than 60 seconds
after water supply.

Whole unit stops
until Reservoir
fills up. Only
Control Water
Valve operates
intermittently for
5 minutes.

Automatically
resets after
Reservoir fills
up.

Water supply
interruption,
Control Water
Valve not opening,
Flush Water Valve
not closing, Float
Switch, Water leak

Abnormal High
Side Pressure

Pressure Switch stays
OFF for 5 seconds.

Whole unit
stops.

Automatically
resets after
Pressure
Switch turns
ON.

Condenser
clogged, Cooling
water circuit,
Refrigeration
circuit

Abnormal Low
Voltage

Voltage stays below
setting for more than 1
second with
Compressor ON and
Control Water Valve
OFF.

c3 blinks.

Automatically
resets after
voltage stays
above reset
setting for 2
minutes.

Supply voltage

Drain Error

Float Switch trips at
upper float level in 10
minutes after Flush
Water Valve turns ON.

Indication only.

N/A

Flush Water Valve
not opening,
Control Water
Valve not closing

Gear Motor
Error

Rotation rate reduces.

Whole unit stops
except Control
Water Valve.

Automatically
resets after 2
minutes.

Gear Motor
overloaded

Содержание FM-300AFE-HC






































































Результаты поиска

Содержание FM-300AFE-HC

Отзывы:

Похожие инструкции для FM-300AFE-HC

Бренды по названию

Популярные бренды

Hoshizaki FM-300AFE-HC, Руководство по обслуживанию

Результаты поиска

Содержание FM-300AFE-HC

Отзывы:

Похожие инструкции для FM-300AFE-HC

Бренды по названию

Популярные бренды