Hoshizaki FM-300AFE-HC Скачать руководство пользователя страница 67

Страница: 67 / 69

2. LOW ICE PRODUCTION

PROBLEM POSSIBLE

CAUSE

REMEDY

1. Gas leaks.

1. See 1 - [5] - a).

2. Refrigerant line

clogged.

2. Replace the clogged

component.

a) Refrigerant Line

3. Overcharged.

3. Recharge.

1. Dirty Air Filter or

Condenser.

1. Clean.

2. Ambient or condenser

water temperature
too warm.

2. Check for recommended

temperature.

3. Condenser water

pressure too low or
off.

3. Check and get recommended

pressure.

4. Fan rotating too slow.

4. See 3 - [1] - a).

b) High-side

Pressure Too
High

5. Water Regulating

Valve clogged.

5. Clean.

c) Expansion Valve

(not adjustable)

1. Low-side pressure

exceeding the limit.

1. Replace.

[1] Low ice

production.

d) Evaporator

1. Evaporator pipe

crushed.

1. Replace.

3. OTHERS

PROBLEM

POSSIBLE CAUSE

REMEDY

1. Bearing worn out.

1. Replace.

2. Fan blade deformed.

2. Replace fan blade.

a) Fan Motor

(Condenser Unit)

3. Fan blade does not

move freely.

3. Replace.

1. Bearings worn out, or

cylinder valve broken.

1. Replace.

b) Compressor

2. Mounting pad out of

position.

2. Reinstall.

c) Refrigerant Lines

1. Rub or touch lines or

other surfaces.

1. Replace.

d) Gear Motor (Ice

Making)

1. Bearing or Gear

wear/damage.

1. Replace.

1. Low-side pressure too

low.

1. See if Expansion Valve Bulb is

mounted properly, and
replace the valve if necessary.

e) Evaporator

2. Scale on inside wall of

Freezing Cylinder.

2. Remove Auger. Use a solution

of lime removing cleaner to
clean periodically. If water is
found to surpass the following
levels, install a conditioner.

Hardness 50 ppm

Silica 30 ppm

f) Heater

1. Broken.

1. Replace.

[1] Abnormal noise

g) CPR (Condenser

Unit)

1. Internal leaks.

1. Replace.

Содержание FM-300AFE-HC






































































Результаты поиска

Содержание FM-300AFE-HC

Отзывы:

Похожие инструкции для FM-300AFE-HC

Бренды по названию

Популярные бренды

Hoshizaki FM-300AFE-HC, Руководство по обслуживанию

Результаты поиска

Содержание FM-300AFE-HC

Отзывы:

Похожие инструкции для FM-300AFE-HC

Бренды по названию

Популярные бренды