manualshive.com logo in svg

Hoshizaki FM-120KE-50-HC, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki FM-120KE-50-HC Скачать руководство пользователя страница 31

28

28

For accurate measurement, use a container to receive ice actually produced for 

10 minutes, measure its weight, and calculate ice production per day. Repeat this three 

times to figure out the average.

c) Model Number

The display shows two digits.

e.g. FM-750AKE(-N), FM-1000AKE(-N) = “05”

d) Software Version

The display shows the software version in six digits/symbols divided into three parts.

e.g. Ver. 9-3-6 = “09”, “-3”, “-6”

The indication is repeated until the maintenance A button is released.

[d] DISPLAYING ERROR LOG

Press and hold the maintenance A button, and press the stop button. The display shows 

the following items one by one every time the stop button is pressed.

This function is available in the ice or stop mode.

Press and hold 

MAINTENANCE A 

Compressor operating hours 

on display ----------

[c] a)

Press  STOP 

Error log

 on display (8 records at maximum)

Press  STOP 

 

“- -” on display (end of error log display mode)

Press  STOP 

Ongoing error 

on display

Release 

MAINTENANCE A 

Note:

1.  The display does not show the ongoing error even if the stop button is pressed while the 

error log is in the display. To display the ongoing error, press the stop button while “- -” 

is in the display to show the end of the error log display mode.

Содержание FM-120KE-50-HC
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды