manualshive.com logo in svg

Horizon Fitness HORIZON T20, Руководство по обслуживанию

Поделиться
Скачать
Horizon Fitness HORIZON T20 Скачать руководство пользователя страница 62

Lower Board Replacement

 

 

Tools required:   

 

 

Philips head screwdriver 

 

Procedure:

 

 
1.  Turn off the power to the treadmill and unplug the power cord from the wall outlet. 
 
2.  With a Philips head screwdriver, remove the motor cover. 
 
3.  Verify that LED MTR is not lit on the lower board. If this LED is lit, please wait 

approximately 1 minute until the light is out. This is an indication that the stored 
power has left the board. 

 
4.  Unplug all the wires and cables from the lower board 

(It is a good idea to note the position of all wiring before removing.)

 

 
5.  With a Philips head screwdriver, remove the lower board, and replace it with a new 

one. 

 

6. 

Reconnect all the wires to the lower board.   

Please refer to lower control board 

wiring diagram.     

 

7.  Install the motor cover. 
 

8. 

Re-plug the power cord, and turn power on.

 

 
 
 
 
 
 
 
 
 
 
 

 

 

62

Содержание HORIZON T20







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды