manualshive.com logo in svg

Horizon Fitness HORIZON T20, Руководство по обслуживанию

Поделиться
Скачать
Horizon Fitness HORIZON T20 Скачать руководство пользователя страница 32

 

E-2 Error-message on the Upper Board 

   

 
 

If there is belt movement upon start up of the treadmill, and an E-2 

message occurs, follow the possible causes below

: 

 

Possible cause:

 

 

• 

Check voltage of wall outlet. 

Warning!    Hazardous voltages will be tested in the following procedure.    Exercise 
extreme caution when performing these procedures.    Do not connect or disconnect 
any wiring, connectors, or other components with the power applied to the treadmill. 

• 

Disconnect the treadmill power cord from the wall outlet.    Using an AC voltmeter, 

verify that the proper AC voltage is present at the wall outlet.    Nominal 120 Vac 
may vary between approximately 105 Vac and 135 Vac.    If the AC voltage is 
missing or incorrect, check the AC service or consult an electrician. 

 
 
 
 
 
 
 
 
 
 

• 

Follow the auto-calibration instructions (reference auto-calibration in table of 

contents). 

• 

If the problem persists, replace the lower and upper boards. 

 
 

 

 

32

Содержание HORIZON T20







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды