horiba 6582S-10C Скачать руководство пользователя страница 25

Страница: 25 / 81

Electrode Preparation

Calibration

Measurement

After Measurement

insing the electrode

Make sure that no dirt and other foreign matters have
adhered to the electrode before measurement.
If dirt and other foreign matters have adhered to the
electrode, rinse the electrode as described in the following
procedure.

Rinse the electrode with pure water.

Wipe off the moisture.

Wipe off the moisture using soft and clean lint-free paper or cloth.

Make sure that there are no dirt and

crystals of internal solution adhered

to the area around the liquid

junction.

If dirt and crystals of internal solution are adhered, they

may affect the outflow of internal solution. Rinse the

electrode with pure water again.

View video

Contamination

Note

Содержание 6582S-10C


















































































Результаты поиска

Содержание 6582S-10C

Отзывы:

Похожие инструкции для 6582S-10C

Бренды по названию

Популярные бренды

horiba 6582S-10C, Инструкция по эксплуатации

Результаты поиска

Содержание 6582S-10C

Отзывы:

Похожие инструкции для 6582S-10C

Бренды по названию

Популярные бренды