Hopkins 594810 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

Hopkins 594810 Скачать руководство пользователя страница 19

Physiological Alarm Messages

Alarm Message

Cause and actions

SPO2 reading will ﬂash.
Alarm lamp is red and
ﬂashing.

A measurement has risen
above the high alarm limit or
fallen below the low alarm
limit. Check the patient's
condition and check if the
appropriate patient type
setting is selected.

Alarm

Level

H

SPO2 reading will ﬂash.
Alarm lamp is red and
ﬂashing.

H

PR reading will ﬂash.
Alarm lamp is red and
ﬂashing.

H

PR reading will ﬂash.
Alarm lamp is red and
ﬂashing.

H

PR and SPO2 reading is
“ - - ”.
Alarm lamp is red and
ﬂashing.

H

The pulse signal was too

weak to be analyzed. Check

the patient's condition,

SpO2 sensor and

measurement site.

Alarm lamp stays
yellow.The screen will
show “Low Perfusion”

The pulse signal was weak

and please pay attention to

sensor location and patient

status.

L

Alarm

SpO2 Too High

SpO2 Too Low

PR Too High

PR Too Low

No Pulse

Low Perfusion

Low signal

Quality

Alarm lamp is yellow
and ﬂashing.The
screen will show “Low
Signal Quality”

M

The pulse signal was too
weak , Check the patient's
condition condition, SpO2
sensor and measurement
site.

Technical Alarm Messages

Alarm

Alarm Message

Cause and actions

Sensor Off

Alarm lamp is yellow
and ﬂashing.The
screen will show
“OFF”

The SpO2 sensor is not applied
to the patient or not connected
to the pulse oximeter, or there
was a fault with the SpO2
sensor, or non-compatibl SpO2
sensor was used. Check that the
sensor application site and the
sensor type are correct, and
make sure that the sensor is
undamaged. Reconnect the
sensor if the sensor is
disconnected or use a new
sensor if the sensor is damaged,
for example, the sensor cable is
broken.

Alarm

Level

M

-19-

«
...
17
18
19
20
21
...
»

Содержание 594810

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды