manualshive.com logo in svg

Hopkins 594810, Инструкция по эксплуатации

Поделиться
Скачать
Hopkins 594810 Скачать руководство пользователя страница 14

Select 

[SET]

→

[ALn]

, and press the 

Up/Down

 button, to turn on/off the 

alarm tone

5.3.3.3   Switch ON/OFF alarm Volume

！

WARNING

：

When the alarm sound is switched off, the pulse oximeter 

will give no audible alarm tones even if a new alarm occurs. Therefore 
the user should be very careful about whether to switch off the alarm 
sound or not.

！

WARNING

：

Do not rely exclusively on the audible alarm system for 

patient monitoring. Adjusting  volume to a low level may result in a 
hazard to the patient. Always keep the patient under close surveillance.

Press the

   

key for 1 second

，

the

   

key will light and the alarm 

messages remain displayed. The alarm will stay silent for 60 seconds.

  

5.3.3.4

 

 Alarm Silence Duration

！

WARNING

：

The 594810 will only keep the last setting. When the 

594810 is turned on, user should check whether the current setting 
meet conditions of patient.

5.3.4  When an Alarm Occurs

When an alarm occurs, observe the following steps to take proper actions:
   1)   Check the patient's condition.
   2)   Confirm the alarm parameter or alarm category.
   3)   Identify the source of the alarm.
   4)   Take proper action to eliminate the alarm condition.
   

Note: 

The pulse rate alarm limit range is 25 to 250.The upper value of the 

pulse rate low alarm limit is limited one number lower than the pulse rate 
upper alarm limit. The pulse rate low alarm limit cannot be set equal to or 
higher than the pulse rate upper alarm limit. In the same way, the pulse 
rate upper alarm limit cannot be set equal to or lower than the pulse rate 
low alarm limit.

Press button 

[SET]

→

[SPO2 L]

 and Press the Up/Down button, set the 

SPO2 value between 20 and 100. 

Note:

The %SpO2 alarm limit range is 20% to 100%. The upper value of 

the %SpO2 low alarm limit is limited to the %SpO2 upper alarm limit. The 
%SpO2 low alarm limit cannot be set equal to or higher than the %SpO2 
upper alarm limit. In the same way,the lower value of the %SpO2 upper 
alarmlimit is limited to the %SpO2 low alarm limit. The %SpO2 upper 
alarm limit cannot be set equal to or lower than the %SpO2 low alarm limit.

5.3.3.2   Set SPO2 Low alarm Limit

 -14-

Содержание 594810

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды