Cleaning hard floors
9. Continue to squeeze trigger and
slowly
pull cleaner back toward you
(second wet stroke). The cleaner rinses
the carpet on the backward pass.
Note:
To assure proper rinsing, it is impor-
tant to keep the cleaner on the same
path backward as forward.
10. Release trigger and slowly push
cleaner forward over area just sprayed
with solution (dry stroke). Then
slowly
pull cleaner back toward you without
squeezing trigger (dry stroke). Continue
using dry strokes until little water is visi-
ble passing through the recovery tank
lid.
How to attach hard floor
brushes and squeegee
Unplug cleaner from electrical outlet.
To prevent possible leaking, remove
clean water tank (Fig. 2-10) and recov-
ery tank (Fig. 2-21). Set tanks aside (do
not set tank on furniture).
1. With handle in upright position, tilt
cleaner back so that handle rests on the
floor.
2. Remove brush assembly with
green
bristles. Attach hard floor brush assem-
bly, with the
white
bristles. (Refer to
Maintenance section, Removable brush-
es, for attaching and removing brush
assemblies.)
3. Lift up rear edge of nozzle (A). Slide
nozzle up and remove from cleaner.
A
4. Position the bottom of the nozzle (A)
inside the squeegee (B), with the tabs
(C) on the squeegee behind the nozzle
as shown.
➡
➡
➡
➡
➡
➡
3-6
3-7
3-9
ON
OFF
WAS
H
AUT
O R
INS
E
Rin
se
3-8
7. Set Rinse Setting switch to
WASH-
AutoRinse
. Turn cleaner ON (Fig. 3-5).
8. Squeeze trigger to release cleaning
solution and
slowly
push cleaner for-
ward (equals one wet stroke).
3-5
12
ON
OFF
WAS
H
AUT
O R
INS
E
Rin
se
WASH
RINSE
12. If you would like to rinse the carpet
with water only, set Rinse Setting switch
to
RINSE
(Fig. 3-8). Repeat steps 8-10.
In this setting, rinsing will be done on
both forward and reverse strokes.
Rinsing is not necessary, but will help
remove detergent residue and help your
carpet look fresher.
13. For heavily soiled areas, repeat
steps 7-10. Avoid saturating carpet, as
noted below.
Note: To avoid saturating carpet, do
not use more than 4 wet strokes over
one area. Always end with dry
strokes.
It is best to alternate wet and dry strokes
as described above.
For best cleaning results and to aid in
faster drying of carpet, end with more
dry strokes. (Continue using dry strokes
until little water is visible passing through
the recovery tank lid.)
14. Empty recovery tank when the
motor sound becomes higher pitched
and there is a loss in suction (see
“Automatic shut-off”, Fig. 2-6).
When finished cleaning, follow “After
cleaning” instructions on page 11.
Carpet Cleaning
Read “Before you begin cleaning”
instructions on page 10.
1. For carpets and rugs, attach the brush
assembly with the green, shorter bristles.
(Refer to
Maintenance
section,
Removable
brushes
for attaching and removing brush
assemblies.)
Do not use hard floor brush
assembly when cleaing carpet.
2. Fill clean water tank according to
instructions for Figs. 2-9 to 2-12.
3. Fill detergent container with HOOVER
Carpet/Upholstery Detergent according
to instructions for Figs. 2-13 to 2-14.
4. Set SpinScrub mode selector to
CARPET TERRAIN
.
5. Dry hands and plug cord into a
prop-
erly grounded outlet.
Do not clean over floor electrical out-
lets.
6. To avoid walking on damp carpet,
start at the end of the room farthest from
the door or path to sink where tanks will
be emptied and filled.
Step on handle release pedal and lower
handle to operating position.
11. For best results, use straight, parallel
strokes as shown in the diagram below.
Overlap strokes by 1 inch to help pre-
vent streaking.
Keep nozzle flat on floor for both forward
and reverse strokes.
3-10
A
B
C
Содержание SteamVac All Terrain Carpet and Hard Floor Cleaner with Auto Rinse Feature Steam Vacuum
Страница 32: ...31...
