draft
5
GB
Please Read Carefully Before Use
Replacing The Dust Bag -
If the bag check indicator flashes please check and, if necessary, replace
the bag (P15).
1.
Press the button (P16) to open the cover and pull the bag collar to remove the bag. The full dust
bag should be disposed of correctly and carefully (P17).
2.
Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder (P17).
3.
Close the cover.
Remember: The bag check indicator may also flash if an obstruction has occurred. In this case refer to
'Removing A Blockage From the System'.
Cleaning the Lifetime Washable Filter -
To maintain optimum performance of your cleaner, please
wash the Pre-Motor filter after each 5 bag changes.
Remove the Pre-Motor filter (P18).Wash it in hand warm water, and allow it to dry thoroughly before
replacing to the cleaner.
Remember: Do not use hot water or detergents. In the unlikely event of the filters becoming damaged,
fit a Genuine Hoover replacement. Do not try and use the product without a dust bag or filter fitted.
Removing a Blockage From The System -
If the bag check indicator is illuminated or flashing (P15):
1.
Check if the bag is full. If so refer to 'Replacing The Dust Bag'.
2.
If it is not full, then;
a.
Do the filters need cleaning? If so refer to 'Cleaning the Lifetime Washable Filter'.
b.
Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the Teletube or flexible hose.
Warning -
The bag check indicator will flash intermittently if the cleaner is used when full, if there is a
blockage or if the filters are dirty. If the cleaner is used for a significant period of time with the bag
check indicator continuously flashing, a thermal cut out will switch the cleaner off to prevent
overheating. The bag check indicator will remain lit once the cleaner has switched off to signal that the
thermal cut out has been activated. If this should happen, then switch the cleaner off, unplug and
correct the fault. It will take about 30 minutes for the cut out to automatically reset.
Please see model specification on packaging label for inclusion of accessories to individual models.
However all accessories can be purchased separately from Hoover.
3 in 1 Tool
- Combines several functions in one, with maximum flexibility by the rotating body. Reach
into awkward areas by rotating the body (P19 and 20). The 3 in 1 tool can be stored neatly underneath
the hose handle (P22).
•
Crevice Tool:
for corners and hard to reach areas. The length can be adjusted by pulling on the
end. Once finished, push to retract (P21)
•
Furniture Nozzle
for soft furnishings and fabrics (P23)
•
Dusting Brush
for bookshelves, frames, keyboards and other delicate areas (P23). To extend the
brushes push the button on the body of the tool
Allergen Remover Turbo Nozzle -
Use the Turbo Nozzle for deep cleaning on carpets. Important: Do
not use the Turbo Nozzle on rugs with long fringes, animal hide, and with carpet piles deeper than
15mm. Do not keep the nozzle stationary while the brush is rotating (P24).
Allergen Remover Mini Turbo Nozzle -
Use the mini turbo nozzle for cleaning stairs and other hard
to clean areas (P25).
Should you have a problem with the product, complete this simple user checklist before calling your
local Hoover Service.
•
Is there a working electricity supply to the cleaner? Please check with another electrical appliance
•
Is the dust bag over-filled? Please refer to 'Cleaner Maintenance'
•
Is the Filter blocked? Please refer to 'Cleaning the lifetime washable filter'
•
Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system'
•
Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically reset
CLEANER MAINTENANCE:
ACCESSORIES:
USER CHECKLIST:
