19
www.hoover.com
G
H
How to attach optional tools
Unplug cleaner from electrical outlet.
1. Place handle in upright position and
remove hose from rack.
All tools attach to the hose in the same
manner:
2. Connect tool to hose by sliding it onto
connector until the tab (G) locks it securely.
Using your thumb, push forward and up on
the latch (H) to remove tool.
Attaching scrub module
(Optional)
1. Open the tool door and remove the Spin-
Scrub™ hand tool.
2. Grasp the sides of the brush module and
lift it from the base (J).
3. Snap scrub module onto the base.
Note:
If may be necessary to rotate the scrub
module (K) slightly so it will align properly
to the base.
J
With a little solution,
test the scrub tool on
a hidden area before
using on the desired
surface. If no surface
change is visible,
continue to use as
described below.
1. Attach hose and
solution tube as
instructed in Figs. 3.14 to 3.15.
2. Place handle in upright position.
3. Fill clean water tank according to instruc-
tions for Figs. 2.9 to 2.11.
4. Fill detergent container with HOOVER
Hard Floor Cleaning Solution according to
instructions for Fig. 2.11.
5. Attach tool to end of hose.
6. Hold scrub tool above area to be cleaned
and press trigger to dispense solution.
7. Release trigger and scrub area with tool.
Pick up dirty solution with squeegee as
shown.
3.19
Using the scrub tool
After using
tool
Drain suction hose
by
turning cleaner ON
and holding nozzle up
for several minutes.
Do not press trigger.
Unplug cleaner from
electrical outlet.
Disconnect hose
and solution tube from
cleaner.
Drain solution tube
by placing round end
in sink and raising
nozzle above your
head. Press the trig-
ger.(Fig. 3.20)
The tool caddy can
be removed and hung
on a coat hanger for
storage or placed
back on the cleaner
(Fig.3.21).
3.20
3.21
3.22
3.23
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
Cleaner won’t run.
Not firmly plugged in.
Plug unit in firmly.
No voltage in wall plug.
Check fuse or breaker.
Blown fuse or tripped
breaker.
Replace fuse or reset breaker.
Low suction.
Recovery tank full/
automatic shut off engaged.
Remove and empty recovery tank.
Blockage In tool on end of
hose.
Remove tool and clear blockage.
Recovery tank lid not on
correctly.
Make sure lid is on securely.
Water tank empty, but
detergent remains.
Fill water tank.
Clean water won’t
dispense.
Clean water tank not firmly
in place.
Make sure tank is securely locked in
position.
Clean water tank or
detergent container empty.
Refill container according to instructions
for surface being cleaned.
Recovery tank lid not on
correctly.
Make sure lid is firmly in place.
Detergent won’t
dispense
Valve cap clogged.
Remove and clean valve cap (see
instructions below).
Brushes/brush
indicator won’t
rotate during
floor cleaning.
Dirty filter screen on bottom
of unit.
Clean screen.
SpinScrub mode selector on
SPILL PICK-UP / OFF.
Slide SpinScrub mode selector to
HARD TERRAIN or CARPET TERRAIN.
HARD TERRAIN setting and
hard floor brushes used on
carpet.
For carpet cleaning, use carpet brush
assembly (green bristles) and set
SpinScrub mode selector to CARPET
TERRAIN.
If a minor problem occurs, it usually can be solved quite easily when the cause is found by
using the check list below.
4. If you have a problem
A
A
B
C
4.3
4.2
4.1
2. Turn valve cap (A)
counterclockwise
and remove.
Soak valve cap in
warm water for at
least 15 minutes.
Wipe cap dry.
3. Align slots (B) on
cap with tabs (C) in
opening.
Turn cap clockwise
to tighten.
To unclog valve
1. Remove clean
water tank.
22
www.hoover.com
